Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Datapath VisionSC-DP2
Summary of Contents for Datapath VisionSC-DP2
- Page 1 VisionSC-DP2 User Guide Version 1.0.4...
-
Page 2: Table Of Contents
Contents Safety Instructions................1 FCC Statement..................2 Introduction..................3 Hardware Overview................4 Software Overview................5 Specification..................7 Unpacking....................8 Installing the Capture Card..............9 Installing Multiple Cards..............11 Firmware Upgrades................12 Software Installation................13 Datapath Limited................14 Index....................15... -
Page 3: Safety Instructions
These ento el equipo, a fin de evitar daños en su producto de Datapath o lesiones al personal instructions should be made available to all those who will use and operate Datapath encargado de su manejo. -
Page 4: Fcc Statement
FCC Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limit are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. -
Page 5: Introduction
The Datapath VisionSC-DP2 offers video professionals the ability to simultaneously capture multiple 4K, Ultra High Definition, video feeds each at 60 frames per second. Developed as part of the VisionSC family of capture cards, the Vision-SC-DP2 offers unmatched capture performance and reliability. -
Page 6: Hardware Overview
DisplayPort Embedded audio (16-24bit, 32kHz-48kHz) Datapath Vision Performance Driver • Multiple cards per system, 16 streams per card • Frame sync and time stamping • Automatic signal detection • Direct Show interface • Datapath RGBEasy API Models VisionSC-DP2 - Dual DisplayPort 1.2 capture card... -
Page 7: Software Overview
User Mode filter for source selection • Enables cropping support in DirectShow on all inputs • Supports Start and Stop trigger interface on all Visi0n inputs Datapath Unified Vision Driver • Multiple cards per system, 16 streams per card • Frame sync and time stamping... - Page 8 • The RGBEasy API for advanced audio and video control • Fully integrated for use with Datapath Wall Control software for video wall applications Multistream Datapath’s MultiStream feature is available on all Datapath capture cards and enables multiple independently formatted video streams to be setup in parallel.
-
Page 9: Specification
Specification Board Format PCI-Express x8 plug-in card, 110mm x 177mm (incl heat sync) Connectors (main board) 2 x locking DisplayPort 1.2 Maximum Capture 616MPixel/second capture bandwidth per channel providing 2 x 3840x2160 at 60Hz. Maximum capture surface of 8k x 8k at Resolution lower frame rates*. -
Page 10: Unpacking
It is recommended that you do not discard the packing box until you are completely satisfied with the VisionSC-DP2 capture card and it is fully installed and working correctly. We also recommend that you make a note of the serial number of the card in a prominent place before the card is plugged into the computer. -
Page 11: Installing The Capture Card
The VisionSC-DP2 card has two locking DisplayPort 1.2 connectors. See Fig. 1 Fig. 1 When removing the DisplayPort cables from the VisionSC-DP2, ensure the release button is pressed on the connector to allow the cable to release freely. (Fig. 2) - Page 12 Fig. 2 Cable Settings When using the VisionSC-DP2 a cable settings function becomes available in the Input Settings of the software application. DisplayPort sources often train the cable link at the maximum available bit rate, even if it is not needed for the required display resolution. Some longer cables may be unable to train reliably at these higher bit rates.
-
Page 13: Installing Multiple Cards
In order to control the order in which the driver uses the cards, it is recommended when installing multiple cards that the links on the VisionSC-DP2 are configured. The example below shows the jumper link settings for up to 32 cards in a single system. When two cards share the same link settings, their order is determined by the PCIe bus. -
Page 14: Firmware Upgrades
Datapath. Whenever a firmware upgrade is performed, the SW2 on the DIP switch must be set ON. The DIP Switch can be located on the back of the VisionSC-DP2 (See Fig. 5 ). To perform the upgrade, follow the step-by-step instructions provided by the upgrade application. The VisionSC-DP2 is shipped with the SW2 switch set at ON, therefore no action should be necessary. -
Page 15: Software Installation
The help file must be located on the local machine to view its content. Using the card with other Datapath products The VisionSC-DP2 captures data and stores it in an on-board video buffer. This data is then copied using DMA to the host system for display, storage or streaming. -
Page 16: Datapath Limited
Datapath Limited Datapath has a long and very successful history in the computer graphics industry. Datapath has been designing and supplying high performance, high quality graphics display systems to the world’s larg- est and most demanding companies and institutions since 1982. Datapath was one of the founding companies of multi-screen Windows acceleration using single and multi board solutions. -
Page 17: Index
Operating System Support 7 Composite Video Capture 7 Copyright Statement 14 Packing box 8 Power Requirements 7 Datapath 14 Power supply 1 Datapath CD 13 Datapath Limited 14 RGBEasy API 4 DIP switch 12 Direct3D 13 Software 13 DirectShow 11...
Need help?
Do you have a question about the VisionSC-DP2 and is the answer not in the manual?
Questions and answers