Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Datapath VisionSC-HD4+
Summary of Contents for Datapath VisionSC-HD4+
- Page 1 The VisionSC-HD4+ Audio/Video Capture Card User Manual Version 1.0.1...
-
Page 2: Table Of Contents
Contents Safety Instructions............................1 FCC Statement...............................2 Introduction................................3 Hardware Overview.............................4 Software Overview............................5 Specification..............................7 Unpacking................................8 Installing the Capture Card........................9 Installing Multiple Cards..........................10 Firmware Upgrades..........................11 Software Installation..........................12 Datapath Limited............................13 Index..................................14... -
Page 3: Safety Instructions
These ento el equipo, a fin de evitar daños en su producto de Datapath o lesiones al personal instructions should be made available to all those who will use and operate Datapath encargado de su manejo. -
Page 4: Fcc Statement
FCC Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limit are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. -
Page 5: Introduction
Introduction The VisionSC-HD4+ has four on board video capture channels; two channels of HDMI 1.4 offering 3840x2160 @ 30 frames per second (fps) and two HDMI 1.3 channels offering 1920x1080 @60fps, all operating independently of each other. This enables four separate video sources to be captured and controlled simultaneously. -
Page 6: Hardware Overview
4096x2160 HDMI 1.4a HDCP 1.4 2096x2096 Audio Capture • Embedded audio support across all four channels. Datapath Vision Performance Driver • Multiple cards per system, 16 streams per card • Frame sync and time stamping • Automatic signal detection •... -
Page 7: Software Overview
Software Overview All Datapath capture cards are supplied with a powerful software application for configuring the format of the input sources and displaying the data. Video Streaming DirectShow drivers for WDM Streaming driver supports the following applications, to encode, record and stream video over networks or the Internet: •... - Page 8 • The RGBEasy API for advanced audio and video control • Fully integrated for use with Datapath Wall Control software for video wall applications Multistream Datapath’s MultiStream feature is available on all Datapath capture cards and enables multiple independently formatted video streams to be setup in parallel.
-
Page 9: Specification
Specification Board Format PCI-Express x8 plug-in card, 110mm x 177mm (incl heat sync) Connectors (main board) 2 x DSM59 connectors plus adapters (see model options) Maximum Capture * 3840 x 2160p 30Hz, 2* 2560 x 1600 60Hz (TBC) Resolution Frame Buffer 768MB Pixel Transfer Formats RGB:5-5-5, 5-6-5 or 8-8-8 (24bit/32bit) -
Page 10: Unpacking
Unpacking Your packing box should contain the following items: • VisionSC-HD4+ - Quad HDMI video capture card and depending on which model ordered, either: • 2 x HDMI splitter cables, or • 2 x DVI splitter cables Fig.3 Note: All plug-in cards are static sensitive and are packed in anti-static material. Please keep the card in its packaging until you are ready to install. -
Page 11: Installing The Capture Card
Installing the Capture Card You are likely to need a flat blade and /or a cross head screwdriver for the installation of the VisionSC-HD4+ card; it would be useful to have these to hand before you begin. • Power down the PC (including peripherals), switch off at the mains and disconnect all the cables connected to the computer, noting the positions for accurate reconnection •... -
Page 12: Installing Multiple Cards
Installing Multiple Cards Multiple cards can be installed in a system providing a large number capture channels. Combinations of Vision capture cards in the same machine are supported by the Vision driver. In order to control the order in which the driver uses the cards, it is recommended when installing multiple cards that the links on the VisionSC-HD4+ are configured. -
Page 13: Firmware Upgrades
The VisionSC-HD4+ cards allow firmware upgrade to be completed on site rather than returning the card to Datapath. Whenever a firmware upgrade is performed, the SW2 on the DIP switch must be set ON. The DIP Switch can be located on the back of the VisionSC-HD4+ (See Fig. 6 ) To perform the upgrade, follow the step-by-step instructions provided by the upgrade application. -
Page 14: Software Installation
Datapath graphics card with the same benefit of non-tearing captures. When the data is displayed on a non Datapath graphics card, the VisionSC-HD4+ sends the data to system memory or direct to the graphics card, dependant on the software used for display. -
Page 15: Datapath Limited
Datapath Limited Datapath has a long and very successful history in the computer graphics industry. Datapath has been designing and supplying high performance, high quality graphics display systems to the world’s largest and most demanding companies and institutions since 1982. Datapath was one of the founding companies of multi-screen Windows acceleration using single and multi board solutions. -
Page 16: Index
Cable 1 Composite Video Capture 7 Operating System Support 7 Copyright Statement 13 Packing Box 8 Datapath 13 Power Requirements 7 Datapath CD 12 Power Supply 1 Datapath Limited 13 DIP Switch 11 RGBEasy API 4 Direct3D 12 DirectShow 10...