Related Manuals for PASI WMS-LTC
Summary of Contents for PASI WMS-LTC
- Page 1 User Manual Temperature Level Conductivity meter P.A.S.I srl – via Galliari 5/E – 10125 TORINO – Italy Tel. +39 011 650.70.33 – Fax +39 011 658.646 - E-mail sales@pasisrl.it www.pasisrl.it...
-
Page 3: Table Of Contents
Table of Contents Table of Contents ......................1 Important Notice ....................... 2 Warranty and safety instructions ................3 Introduction ....................... 4 Technical Specifications ................... 5 Probe ..........................5 Temperature ........................6 Conductivity ........................6 Level Indicator ......................6 Power supply ......................... 6 Display .......................... -
Page 4: Important Notice
1. Important Notice All rights to this manual are owned solely by P.A.S.I. srl. All rights reserved. P.A.S.I. software and programs are delivered "as is". P.A.S.I. products have not been designed to be used in any way or application other than those mentioned. -
Page 5: Warranty And Safety Instructions
Faultless and safe operation of the device can be guaranteed only if the transport, storage, handling and operation of the device is appropriate. To avoid damage, use only original accessories or approved by PASI srl. When a suitable location has been selected for the instrument, you must ensure that water does not flow into the device under any conditions. -
Page 6: Introduction
3. Introduction The instrument WMS-LTC is a device designed and assembled by PASI srl. The WMS-LTC is a conductivity, temperature and level meter. The instrument is equipped with a display on which the temperature and conductivity indications are shown. The water level will be visible on the cable marked in centimetres. -
Page 7: Technical Specifications
PUR. Graduation in centimeters, printed in black on the cable itself, with meter-decimeter indication Probe Probe diameter 20mm Probe length 200mm Materials Stainless steel body, plastic protective cap/cover WMS-LTC... -
Page 8: Temperature
Temperature Unit of measure °C o °F Measuring range from -10°C to +60°C or from 14°F to 140°F Precision +/- 0.2°C or +/- 0.4°F Conductivity Unit of measure µS/cm or mS/cm normalized at @25°C Range from 40µS/cm to 80000µS/cm Precision +/- 5% of the reading Level Indicator Sensitivity... -
Page 9: Display
When the batteries are flat, the instrument will automatically switch off and display a low battery message accompanied by a warning light and sound signal Display Backlight Line 1 Conductivity Line 2 Temperature User Interface Push-button Single button for on / off and settings WMS-LTC... -
Page 10: User Interface, Functionality And Maintenance
5. User Interface, functionality and maintenance Panel The panel on the instrument shows information about the instrument and its functions. The 2 lines on the display show respectively: Conductivity level normalized to 25°C; Temperature. Conductivity is displayed in: ... -
Page 11: Functionality
Press and hold the “ON/OFF” button, until the sound signal and light are activated. Back-lighting The backlight is activated with a single short press of the "SETTING" button. It will remain active for about a minute and a half. WMS-LTC... -
Page 12: Changing The Unit Of Measure Of The Temperature
The detection of the water level may be inaccurate due to the formation of water residues on the probe after extracting it from the water. For this reason the WMS-LTC is equipped with an automatic level detection system. When there is high conductivities, however, manual selection of sensitivity may be more effective. -
Page 13: Calibration
Maintenance To keep your instrument in perfect condition, remember to carefully clean the cable and sensor and dry them with a soft cloth after use. WMS-LTC... - Page 14 To clean the probe it is recommended to use denatured ethyl alcohol and then rinse it in distilled water. This procedure is very important to get an accurate reading.
-
Page 15: Take A Measurement
Take a measurement 6. Take a measurement The use of the WMS-LTC instrument is very easy. After switching on the instrument, the conductivity, temperature and level can be read. The probe has a certain thermal inertia and to obtain an accurate reading of conductivity and temperature it is necessary to leave the probe immersed for at least 5 minutes.