60" fireplace media console with built in bluetooth speakers and 28" modern infrared electric insert (45 pages)
Summary of Contents for Greentouch 2330FM-23-350
Page 1
MENARDS ITEM #641-5290 MODEL #2330FM-23-350 ATTACH YOUR RECEIPT HERE 33” ELECTRIC FIREPLACE ASSEMBLY, CARE & USE INSTRUCTIONS Serial Number__________________ Purchase Date__________________ Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-855-571-1044 9 a.m. - 5 p.m., EST, Monday - Friday. www.greentouchhome.com.
PACKAGE CONTENTS PART DESCRIPTION QUANTITY PART DESCRIPTION QUANTITY Fireplace Brick Bottom Panel Left Wall Fireplace Glass Front Right Wall Bottom Front Panel Left Support Panel Fire Log Right Support Panel Fireplace Grate Upper Front Panel Remote Control (Battery Center Shelf (with heater) Inside) Fireplace Brick Wall...
HARDWARE CONTENTS (NOT SHOWN ACTUAL SIZE) Wooden Dowel Connecting Locknut Long Bolt Washer Long Screw Touch-up Pen x 11 x 21 x 12 x 11 x 12 L-Bracket Screw Bolt Tip Restraint Hardware SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC rules.
Page 5
SAFETY INFORMATION (CONTINUED) Modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment. This Class B digital apparatus complies with Canadian ICES-003. IMPORTANT INSTRUCTIONS When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: DANGER •...
Page 6
SAFETY INFORMATION (CONTINUED) • Each surface intended to support a load shall have a corresponding statement in the use instructions specifying the maximum intended load for that surface in pounds (kilograms). • Risk of electric shock-connect this furnishing to a properly grounded outlet only. See Grounding Instructions. •...
Page 7
SAFETY INFORMATION (CONTINUED) Electrical Connection • A 15-Amp, 120-volt, 60 Hz circuit with a properly grounded outlet is required. Preferably, the fireplace will be on a dedicated circuit as other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in operation.
PREPARATION Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 40 minutes Tools Required for Assembly (not included): Phillips screwdriver ASSEMBLY INSTRUCTIONS 1.
Page 9
ASSEMBLY INSTRUCTIONS (CONTINUED) 2. Insert six wooden dowels (AA) & six locknuts (CC) into the corresponding holes on the upper front panel (F) and bottom front panel (K). Turn the locking nut 180 degrees clockwise to secure the walls (B, C). Wooden Dowel Locknut 3.
Page 10
ASSEMBLY INSTRUCTIONS (CONTINUED) 4. As shown in the diagram, align holes on the fireplace brick bottom panel (I) with the holes of wood cleats on the side of the assembly from step 3. Secure by tightening the five long bolts (DD) and five washers (EE) with a Phillips screwdriver. Long Bolt Washer 5.
Page 11
ASSEMBLY INSTRUCTIONS (CONTINUED) 6. Screw six connecting rods (BB) into the designated holes on the back of the top (A). Connecting Rod 7. Insert eight wooden dowels (AA) & six locknuts (CC) into the corresponding holes on both left wall (B), right wall (C) and upper front panel (F).
Page 12
ASSEMBLY INSTRUCTIONS (CONTINUED) 8. Attach the fireplace glass front (J), lowering it into the front groove on fireplace brick bottom wall (I). Secure the glass by turning the pre-assembled plastic knobs. 9. With assistance from another adult, place the assembled panels face down onto a scratch-free surface. Insert three wooden dowels (AA) into the corresponding holes on the upper front panel (F), align the center shelf (G) with the inserted wooden dowels and lower into place.
Page 13
ASSEMBLY INSTRUCTIONS (CONTINUED) 10. Position the fireplace grate (N) by inserting the bottom pins of the fireplace grate (N) into the holes on the fireplace brick bottom wall (I), secure by tightening two bolts (JJ) with a Phillips screwdriver. Bolt 11.
Page 14
ASSEMBLY INSTRUCTIONS (CONTINUED) 12. Screw two L-bracket (HH) onto the fireplace brick wall (H) using four screws (II). L-Bracket Screw 13. Align the USB cable from behind through the cable hole on the fireplace brick wall (H). Attach the USB cable from the heater into the USB port behind the fireplace grate (N).
Page 15
ASSEMBLY INSTRUCTIONS (CONTINUED) WARNING: You must install the tip restraint hardware to help prevent any accidents or damage to the unit. We strongly recommend attaching the tip restraint hardware to a wall stud and your unit. For all other wall types, please visit your local hardware store to obtain the proper hardware.
OPERATING INSTRUCTIONS Control Panel Remote Control To use the remote control, first remove the plastic tab by gently pulling it out of remote control. Controls and Display The control panel will display the heater setting when the unit power is turned ON. Whichever control icon you press will display the current setting of the corresponding function.
Page 17
OPERATING INSTRUCTIONS (CONTINUED) Heater Function • Press the HEATER ICON to display the current heater setting. • Press the HEATER ICON again to scroll down through the heater settings. Note: Long-hold the icon to quickly scroll through settings. • Set the heater to “HI” (High) to have the heater run continually. •...
CARE AND MAINTENANCE • Make sure the unit is turned OFF, unplugged and the heating elements of heater are cool whenever you are cleaning the heater or fireplace. • Clean the metal trim using a water-dampened soft, clean cloth. DO NOT use brass polish or household cleaners as these products will damage the metal trim.
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Error E1 displayed on The overheat sensor has Unplug unit, wait 15-20 minutes, then the sensor will reset control panel. been engaged. itself. Plug the unit back in and turn on the heater. If the problem persists, call customer service (1-855-571-1044).
ONE-YEAR LIMITED WARRANTY The manufacturer warrants that your new electric fireplace is free from manufacturing and material defects for a period of one year from date of purchase, subject to the following conditions and limitations. Install and operate this electric fireplace in accordance with the installation and operating instructions furnished with the product at all times.
Right Wall 2330FM-23-350-RIGHT WALL Upper Front Panel 2330FM-23-350-UPPER FRONT PANEL Fireplace Brick Wall 2330FM-23-350-INSERT WALL BRICK Fireplace Brick Bottom Panel 2330FM-23-350-INSERT BOTTOM WALL BRICK Fireplace Glass Front 2330FM-23-GLASS FRONT Bottom Front Panel 2330FM-23-350-BOTTOM FRONT PANEL Fire Log FIRE LOG 1...
Need help?
Do you have a question about the 2330FM-23-350 and is the answer not in the manual?
Questions and answers