Attention: pour eviter les chocs electriques, introduire la lame le plus large de la fiche dans la borne corre- spondante de la prise et pousser jusqu'au fond. Important: One Federal Court has held that unauthorized recording of copyrighted TV programs is an infringement of U.S. copyright laws.
équipements produisant des interférences au suggestions. You may find the booklet called How Canada. to Identify and Resolve Radio/TV Interference Problems helpful. This booklet was prepared by European Notice the Federal Communications Commission. It is Products with the CE Marking comply with both available from the U.S.
Important Warranty Information Regarding Television Format Viewing Wide screen format PDP Displays (16:9,the aspect ratio of the screen width to height) are primarily designed to view wide screen format full-motion video.The images displayed on them should primarily be in the wide screen 16:9 ratio format,or expanded to fill the screen if your model offers this feature,and con- stantly moving.Displaying stationary graphics and images on screen,such as the dark side-bars on non- expanded standard format television video and programming,should be limited to no more than 5%of the total television viewing per week.
Your New Plasma Display Panel Front Panel POWER SOURCE, MENU, VOLUME (-,+), Remote Control Signal Receiver Press to turn SELECT ( , ), MUTE Aim the remote control towards the PDP on this spot on the Monitor. and off. Checking Parts Remote Control/ PC Cable Ferrite Cores (7EA)
Remote Control Buttons Remote Control Œ Power button Turns the PDP on and off. ´ Number buttons ˇ Display button Press to display information on the PDP screen. ¨ Menu button Displays the main on-screen menu. ˆ CH (Channel) and VOL (Volume) buttons Channel and Volume buttons are used for selecting menu item in menu mode.
Wall Installation Instructions Installation Notes Do not install the PDP on any place other than vertical walls. To protect the performance of the PDP and prevent troubles, avoid the following. • Do not install next to smoke and fire detectors. •...
Page 9
Remove six large screws from the rear side of the display. Insert the bolts, dish-type washers, and insulation holder into the holes as shown in the following figure: Œ Bolt ´ Insulation holder Hang the protruding plastic part on the rear of the PDP up the groove on the top of the wall attachment panel.
Turning the Monitor(PDP) On and Off Turning the Monitor(PDP) On and Off Press the Power button on the remote control. The PDP will be turned on and you will be ready to use it’s features. You can also use the Power button on the front of the PDP.
Connecting Speakers Speaker Audio Cable The speakers MUST have more than 7watts rating (impedance 8ohm). How to Connect Connect the speaker audio cable to the external speaker output jack on the rear of the PDP matching the “+” and “-” ends of the cable with the diagram on the PDP. Connecting PDP and Speakers / Stand and Speakers Fix the bracket onto the guide pole located on the rear of speaker and fasten the screws.
Connecting a DVD/Set-Top Box Power Plug Video (Y, P ) Cable Audio Cable How to Connect Connect a Video cable between the DVD/Set-Top Box (Y,P Top Box and the Component1/2 Video Input (Y,P ) Input jacks on the PDP. • You can attach the (supplied) to the both jacks of the Video cable.
Customizing the Picture You can use the on-screen menus to change the Brightness, Contrast, Sharpness, Color, and Tint settings of your PDP. Press the Menu button, then press the joystick to enter. Move the joystick left or right to select the “Custom”. You will also see the items “Contrast”, “Brightness”, “Sharpness”, “Color”...
Viewing the Picture-in-Picture Selecting the PIP Screen Press the Menu button. Move the joystick up or down to select the “PIP”, then press the joystick to enter. Quick way to access the PIP: Just press “PIP” on the remote control. Move the joystick left or right to select the “On”.
Changing the Location of the PIP Image Press the Menu button. Move the joystick up or down to select the “PIP”, then press the joystick to enter. Quick way to access the PIP location: Just press “Locate” on the remote control. Move the joystick up or down to select the “Locate”.
Freezing the Picture Still Press the Still button on the remote control to freeze a mov- ing picture into a still one. Press again to cancel. Sound Control Customizing the Sound ...34 Using Automatic Sound Settings ...35 Using the Surround ...36...
Customizing the Sound Press the Menu button. Move the joystick up or down to select the “AUDIO”, then press the joystick to enter. Move the joystick left or right to select the “Custom”. You will also see the items “Treble”, “Bass”, “Balance”...
Using the Surround Press the Menu button. Move the joystick up or down to select the “AUDIO”, then press the joystick to enter. Move the joystick up or down to select the “Surround”, then move the joystick left or right to select the “Concert”, “Hall”...
Setting the Clock This PDP has a built-in clock that will appear on screen when you press the Clock Display button on the remote control. Setting this clock also allows you to use it to automatically turn the PDP On or Off. Press the Menu button.
Setting the Timers This PDP can be set to turn on or off automatically at specific times that you choose. Before using the timers, you must set the PDP’s clock, as described previously. Setting the On/Off Timer Press the Menu button. Move the joystick up or down to select the “TIME”, then press the joystick to enter.
Connecting PC and Operation Connecting to a PC ...44 Adjusting the PC Screen ...48 Changing the Position of the Image ...49 Changing the Size of the Image ...50 Enlarge of the Image (Zoom)...51 Move Expanded Picture ...52 Picture Quality Adjustment ...53 Information ...56 Power Saver (PC mode only)...57...
Connecting to a PC This PDP set is not compatible with Macintosh PC. Power Plug PC (15pin) Audio Cable Cable Cable Connecting a PC to the PDP Connect a PC (15pin) or BNC cable between the Video Output jack on the PC and the RGB1 (15p D-SUB) or RGB2 on the PDP.
Page 24
How to Set up Your Display Setting (Windows only) Notes: The plasma panel of this monitor is composed 1366 pixels & 768 lines. That is, the best resolution of this monitor is 1366 X 768. Thus, select 1366 X 768 resolution in same way as below when you control the display setting, If your video card does not support 1366 X 768 resoution, the resolution of 1024 X 768 is recommended.
Adjusting the PC Screen Adjusting the R.G.B Preset: • Press the RGB button to select the PC mode. Press the Menu button, then press the joystick to enter. Move the joystick up or down to select the “Color Control”, then move the joystick left or right to enter. Move the joystick up or down to select the item you want to change.
Changing the Size of the Image Preset: • Press the RGB button to select the PC mode. Press the Menu button. Move the joystick up or down to select the SETUP, then press the joystick to enter. Quick way to access the Size: Just press “Scaling”...
Move Expanded Picture Preset: • Press the RGB button to select the PC mode. Press the Menu button. Move the joystick up or down to select the SETUP, then press the joystick to enter. Quick way to access the Zoom: Just press “Zoom/Pan”...
Page 28
Frequency Adjustment Preset: • Press the RGB button to select the PC mode. Press the Menu button. Move the joystick up or down to select the SETUP, then press the joystick to enter. Move the joystick up or down to select the “Image Lock”, then move the joystick left or right to enter.
Information Preset: • Press the RGB button to select the PC mode. Press the Menu button. Move the joystick up or down to select the SETUP, then press the joystick to enter. Move the joystick up or down to select the “Miscel- laneous”, then move the joystick left or right to enter.
Selecting a Menu Language Press the Menu button. Move the joystick up or down to select the “SETUP”, then press the joystick to enter. Move the joystick left or right to select the appropri- ate language: English, Spanish, or French. Press the Menu button to exit.
Using the Key Lock When setting Key Lock ON, the buttons (SOURCE, MENU, VOLUME, SELECT, MUTE, POWER) on the front of the PDP don’t operate. But those buttons will operate when setting Key Lock OFF. Press the Menu button. Move the joystick up or down to select the “SETUP”, then press the joystick to enter.
Troubleshooting Before you call a service technician, please scan this list of problems and possible solutions. It may save you time and money. Problem Possible Solution Poor picture. Check all wire connections. The power indicator is amber The monitor is using its power management system. blinking.
This PDP applies to Class B digital device. (Note: Class B system is for home use.) This PDP has been accepted as a device with proper electrowave and you can use this PDP not only in a residential area but other areas. PDP5090 Model Dimensions Display 1208.5 (W) X 89 (D) X 724 (H) mm ;...