1. Safety and Precautions CAUTION * The service of this LCD TV must be carried out by qualified persons only. * Do not change any module unless the set is switched off. CLEANING:Always disconnect unit from mains supply before attempting to clean it. Use soft cloth moistened with soapy water, wipe gently.
Page 4
Don’t listen to headphones at high volume, as such use can permanently damage your hearing. Don’t obstruct the ventilation of the equipment, for example, with curtains or soft furnishings. Overheating will cause damage and shorten the life of the equipment. Don’t allow electrical equipment to be exposed to rain or moisture.
3. Connection & Applications SCART VIDEO S-VIDEO Component Pb/Cb Pr /Cr AC IN...
Page 9
D-SUB CONNECTOR PC AUDIO IN HEAD PHONE AUDIO IN 1 / OUT(R/L) AUDIO IN 2 (R/L) 75Ohm AERIAL INPUT SOCKET HEAD PHONE SPEAKERS VIDEO AERIAL NOTE: Audio out : The level of audio output cannot be changed using the volume , treble , and bass controls on your TV .
4. Controls Location The buttons control your TV’s basic features, including the on-screen menu. To use the more advanced features, you must use the remote control. POWER: turn on or turn off the LCD TV. SOURCE: set up the input source (PC, TV, SCART Video/ SCART RGB , Video, S-Video, Component) MENU: display the main menu.
5. Remote Control The remote control pad works almost same as ordinary TV remote control that includes the basic function needed while viewing a live video. DISPLAY : Display the current source or program digits .
Summary of Control Buttons Selecting the Signal Source Switch to the TV mode. Switch to the PC mode. SCART Switch to the Video mode or RGB mode from SCART. VIDEO/S-V Switch to the Video mode from RCA socket or S-Video mode. COMPONENT Switch to the Component mode (YPbPr or YCbCr).
REVEAL Press “REVEAL“ button to display concealed information, such as solutions of riddles or a quiz. EXPAND Press “EXPAND“ button to enlarge the top half or bottom half of the Teletext page. SUB-PAGE/TIME Press “SUB-PAGE/TIME“ button to access to the sub-page you required.
6. Disassembly Instructions 1. Face down the LCD-TV : Face down the LCD-TV on a smooth plane with a soft material to protect the panel faceplate . 2. Tuner Board Removal : Note: If only repair the Tuner Board , need not disassemble the Base and Back Cover.
Page 15
3. Base Removal : 3.1 Remove 5 screws from the bottom of the Base. (Indicated as “ A ”) 3.2 Push upward and take the Base apart from the Neck. (Indicated as “ Arrow ” ) 4. Neck Removal : 4.1 Remove 2 screws from Neck Cover.
Page 16
4.3 Remove 4 screws from the Neck and then take Neck apart from the Back Cover. (Indicated as “ C ”) 5. AV Cover (I/O Board) Removal : 5.1 Loosen 2 screws. ( Indicated as “ E ”) 5.2 Pull out the AV Cover (I/O Board) directly. ( Indicated as “...
6. Back Cover Removal: 6.1 Remove 8 screws from the Back Cover . ( Indicated as “ F ” and “ G ”) 6.2 Take Back Cover apart from the LCD-TV. 7. Right / Left Side Covers Removal : 7.1 Remove 4 screws from 2 Slides of I/O Board & Right Side Cover. (Indicated as “ H ”) 7.2 Remove 3 screws from the Power Case Assembly.
Page 18
8. Main PCB Shield Removal : 8.1 Remove 2 screws from Main PCB Shield. (Indicated as “ K ” ) 8.2 Remove 2 Hexagonal screws from the D-Sub Connector. (Indicated as “ K’ ”) 8.3 Take Main PCB Shield apart from Panel Bracket . K’...
Page 19
10. Panel Bracket Removal : 10.1 Remove 5 screws from the Panel Bracket . (Indicated as “ M ”) 10.2 Take Panel Bracket apart from the Front Cover . -17-...
8. Troubleshooting 8.1 Symptom Codes ( for Call Center use ) CODE SYMPTOM COUNTERMEASURES • No Picture and No Sound Make sure the Power cord and Aerial Cable are in TV mode. properly connected . • Make sure the batteries in remote control are not flat. •...
Page 22
CODE SYMPTOM COUNTERMEASURES • Stripe noise . Check the coaxial cable connected with the TV is not oxidized • Do not use 300 ohm twin lead cables as interference may occur • It is recommended to use a 75 ohm coaxial cable (not supplied) to get premium quality picture.
Page 23
CODE SYMPTOM COUNTERMEASURES • “Out of Range” message Maximum PC resolution supported is 1024x768 / 1280 x 768, so the screen will appear “Out of range” at higher resolution. • Reduce the resolution to 1024x 768/ 1280x 768 from PC . •...
8.2 Flow Chart ( for Repair Center Use ) (1) Power Start NG No Backlight & No LED Is the Voltage of P803#10 5V & PB01 Replace P803# 4 24V ? (Power Module) (on Power Module) Is the Voltage of connectors Check L139 24V ?
(2) No Backlight , but LED lights up No Backlight ,but LED lights up Still No Replace backlight Which Color does Green Check & Re-plug U901 (Inverter) P802 & P802A Display ? ( from Power to I019 (Scaler) Inverter) POWER Press key &...
Page 26
(3) No picture , but Backlight & LED light up No Picture , but Backlight & LED light Up Is the Voltage of L042 5V Replace Q003/I027/L095 (Panel 5V I/P) ? Do all of the Replace Does have sources have No I001 picture? Picture ?
Page 27
(4) Picture Abnormal or Halt Picture Abnormal / Halt Steps to Refresh EEPROM : StepsM After pressing 1. Press POWER key to turn off RESET button ,does the the LCD-TV. picture recover normal? 2. Press CH. Down key on the top of LCD-TV (don’t release ) and then press POWER After pressing...
Page 28
(5) Frame Defects or Striped Lines at all sources The Ver. or Hor. Sync. haven’t been held at all sources. Are the Outputs of Does the wire Does the wire I019 (TP6760) P005A connect P005A connect V901 Replace normal ? firmly with LCD firmly to P005 ? (LCD Panel )
9. Electronic Circuit Description 9.1 Main Board Circuit 1) Power Refer to sheet 7 of PWB-0663 circuit diagram. AC 110V~220V is applied to the LCD-TV through socket P801 on PB01 ( Power module: PWB-0656) . PB01 (Power module: PWB-0656) outputs DC+24V to Inverter U901 via P802 #1~#5 .
Page 30
3) TV Signal Refer to sheet 4 、 8 、 9 of PWB-0663 circuit diagrams. The IEC plug on tuner UT01 receives TV picture and Sound signals from aerial .Tuner UT01 (Tuner-FQ1216ME/MK3) is a multi-standard TV tuner for CCIR B/G, D/K, I, L/L’ system and the front-end has a built-in digitally (I C) PLL tuning system .
Page 31
5) Panel interface Refer to sheet 6 of PWB-0663 circuit diagrams. The signals of panel interface are all applied from Scaler I019 (TP6760) to LCD Panel through connector P005 and wire P005A . The signals CLK 、 DE 、 V.SYNC 、 H.SYNC from I019 #90,#92~94 are applied to LVDS IC I014 # 31,#30,#28,#27 and output PCLK-,PCLK+ at #39,#40 .Then , signals are applied to Panel via connector P005 #7, #6 and used for panel display controls.
Page 32
9.2 Tuner Board Circuit Refer to Tuner Board circuit diagrams of PWB-0564 in Chapter 10.3. UT01 (Tuner-FQ1216ME/MK3) is a multi-standard TV tuner for CCIR B/G, D/K, I, L/L’ system and the front-end has a built-in digitally (I C) PLL tuning system . The Output of Composite Video from QT01 #Emitter fed with Tuner UT01 is applied to SAA7118 through PT01 #23 、...
Page 33
9.3 Key、LED&IR Board Circuit Refer to Key 、 LED & IR circuit diagram of PWB-0565 in Chapter10.2 and sheet 5 of PWB-0663 circuit diagram(Main Board). * Key : The Keyboard is connected with Main Board through socket P021 and wire P021A and to control the I012 (MCU) .So , if the operation of key is fail , the I012 (MCU) may fail .
14. Mechanical Parts List 14.1 Parts List of 27” : CKT NO. PARTS NO. DESCRIPTION FRONT COVER 5642292101 SP-SCREEN 5642317800 NON-WOVEN FABRICS 5642028106 METAL-MESH-SPEAKER 5642514000 IR LENS 5040331300 INSULATION-INVERTER 5646503600 5642725600 LCD MBRACKET TUNNER PCB CLAMP 5642678700 5642847107 BRASS SPACER WIRE MOUNTS 5642679000 POWER PCB SHIELD...
Page 63
14.2 Parts List of 30” : CKT NO. DESCRIPTION PARTS NO. Front Cover 5642291902 Back Cover 5642292002 Neck Front Cover 5641412503 Neck Back Cover 5641412603 Base 5641412703 AV Cover Hole 5642420202 AV Cover 5642318004 Signal Cover 5642318104 Tuner Cover 5642318204 IR Lens 5640331300 Tuner PCB Clamp...