Download Print this page

TRP EVO12 Installation Instructions Manual

Drive train
Hide thumbs Also See for EVO12:

Advertisement

Quick Links

EVO12 DRIVE TRAIN
Manual, installation instructions, compatibility chart

Advertisement

loading
Need help?

Need help?

Do you have a question about the EVO12 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for TRP EVO12

  • Page 1 EVO12 DRIVE TRAIN Manual, installation instructions, compatibility chart...
  • Page 2 Chainlines & Q-factors Chainline Q-factor Crank Chainring Chainring Offset Chainline Q-factor OFFSET M9050/8050 3mm Boost 52mm 178mm M9050 M8050 M8070 49mm 178mm M8070 M8070 56mm 193mm...
  • Page 3 BSA BB - M8000 Determine the type BB shell Fully assembled Non-drive side Drive side Use the following BB model of your BB shell frame width width spacer usage spacer usage crankset ( Right Side ) ( Left Side ) FC-M9050 68mm 96mm...
  • Page 4 : 68 丶 83mm : 73mm Measure the width of the frame. Check the TRP BB & Crankset Compatibility Chart to ensure that you are choosing the correct bottom bracket. : 68 丶 83mm ( 2 x 2.5mm ) : 73mm ( 1 x 2.5mm )
  • Page 5 Use a standard press fit tool Measure the width of the frame. to install the right-side cup into the frame. Check the TRP BB & Crankset Compatibility Chart to ensure (Use Bearing Cup Press tool to install) that you are choosing the correct bottom bracket...
  • Page 6 Chainring Installation Guidance Installation order and direction Use an ISIS Drive™ BB tool to install the chainring lockring along with the 35 x 44 x 0.1 washer onto the drive-side crank. Tighten the lockring to 40 Nm (30ft-lbs).
  • Page 7 Chainring / Chain Set Up Using the icon on your TRP chainring, make sure to align the wide link of the chain with the inner teeth of the chainring...
  • Page 8 HEX 10mm 50Nm (37ft.lbs) Tighten the drive side crank Check the TRP BB & Crankset Compatibility Chart to make sure your TRP crankset is compatible Gently tap until the crank arm is fully seated against the bearing...
  • Page 9 CS-M8070-7 Cassette Installation Install the provided DH spacer Install the cassette onto the freehub body onto the freehub. starting with the 5 largest cogs. Install the remaining two cogs onto the freehub ensuring the wide groove and wide spline line up. Install the lockring with a Cassette Lockring tool.
  • Page 10: Installation

    CS-M9050-12 Cassette Installation Using a cassette lockring tool, turn the lockring counter-clockwise until completely removed. Hold the cassette in place Removal with cassette pliers or a chain whip tool. Remove the cassette by pulling the cassette away from the freehub. Install Installation the lockring with a...
  • Page 11 EVO RD & SL USER MANUAL EVO RD & SL USER MANUAL Installa�on of Derailleur & Shi�er / Montage des Schaltwerks und Schalthebels Installa�on of Derailleur & Shi�er / Montage des Schaltwerks und Schalthebels Fig. 1 Fig. 7 Derailleur Installation / Montage des Schaltwerks Derailleur High Limit Adjustment / Einstellung der Anschlagsbegrenzung für das With the bike in a work stand, ensure the derailleur hanger is straight using a hanger kleinste Ritzel...
  • Page 12 EVO RD & SL USER MANUAL EVO RD & SL USER MANUAL Installa�on of Derailleur & Shi�er / Montage des Schaltwerks und Schalthebels Installa�on of Derailleur & Shi�er / Montage des Schaltwerks und Schalthebels Fig. 13 Fig. 20 B Gap Adjustment / Einstellung des oberen Schaltrollenabstandes (Umschlingungss- Advance Lever Adjustment / Einstellung des unteren Schalthebels chraube) Adjust the position of the advance lever (if desired) by loosening the two T10 Torx bolts...