1. Manuals
  2. Brands
  3. ZEEWEII Manuals
  4. Test Equipment
  5. DSO1511G
  6. User manual

ZEEWEII DSO1511G User Manual

Handheld oscilloscope
Hide thumbs
Table of Contents

Advertisement

Quick Links

ZEEWEII
DSO1511G
HANDHELD OSCILLOSCOPE
User's Manual
Designed by zeeweii
DSO1511G

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DSO1511G and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ZEEWEII DSO1511G

Summary of Contents for ZEEWEII DSO1511G

  • Page 1 ZEEWEII DSO1511G HANDHELD OSCILLOSCOPE User’s Manual Designed by zeeweii DSO1511G...
  • Page 2 ① Current trigger mode: Auto/Normal. ② A thumbnail view of the current window and memory. ③ Trigger edge: rising/falling. ④ Battery remaining power. ⑤ The position of the trigger level. ⑥ The waveform type of the generator. When it is closed, no display. ⑦...
  • Page 3 Button Function 1.Normal function OK/Auto 1.When the menu is opened, it acts as the "OK" function. 2.When the menu is not open, it acts as an "automatic" function. Run/Stop 1.Short press once to stop sampling, click again to run. 2.Long press to open the square wave generator window. Xkey/Power 1.

  • Page 4: Table Of Contents

    TABLE OF CONTENTS 1 SAFETY PRECAUTIONS ............. 5 2 PROBES ................... 6 ....................... 6 ROBE CALIBRATION ......................6 ROBE BANDWIDTH ..................... 6 ROBE WITHSTAND VOLTAGE ..........................7 SE TIPS 3 VERTICAL SYSTEM ............7 ...................... 7 ERTICAL SENSITIVITY ......................8 ERTICAL POSITION 4 HORIZONTAL SYSTEM ..............

  • Page 5: Safety Precautions

    6.12 ........................12 ENERATOR 6.13 ....................... 12 IDEO OUTPUT 6.14 PC ......................12 ONNECT TO 6.15 ........................13 URSOR 7 MENU INTRODUCTION ............13 ........................... 13 HANNEL ........................13 EASUREMENT ..........................14 RIGGER ..........................14 ISPLAY ..........................14 ........................... 15 ETTINGS 1 Safety Precautions Learn about the following safety precautions to avoid injury and prevent damage...

  • Page 6: Probes

    2 Probes 2.1 Probe calibration The probes delivered with this machine have been compensated and do not need to be calibrated again. If you use another new probe before the first use, it must be calibrated before it can be used normally, otherwise the measurement will be inaccurate (only for the 10X/100X).

  • Page 7: Use Tips

    which is usually 600V(dc+ac). 2.4 Use tips 2.4.1 Large input capacitance Because the probe 1X has a large input capacitance (usually more than 100 pf), it is not suitable for measuring some capacitively sensitive circuits. For example, when measuring a passive crystal of MCU, the large capacitor may cause the crystal to fail to vibrate.

  • Page 8: Vertical Position

    3.2 Vertical position The method of moving the waveform up and down: directly press the up and down keys to move the waveform up and down. In addition: By default, the up and down keys move the waveform. If you need to move the trigger level, you need to hold down the “Power”...

  • Page 9: Trigger System

    Trigger system About trigger The oscilloscope will capture a frame of waveform only after the waveform meets the pre-set conditions. This action of capturing the waveform according to the conditions is the trigger. What does trigger do? 1. Trigger can stabilize the waveform on the screen. 2.

  • Page 10: Operation Guide

    the running state, the user can move the trigger position by pressing the left and right buttons.。The trigger position is shown on the screen as an arrow. 6 Operation Guide 6.1 POWER In the shutdown state, long press the "POWER" button to turn on the machine, and then release the button when the screen is on.

  • Page 11: Run/Stop

    6.6 Run/stop In the running state, click the "Run/Stop" button to stop the oscilloscope. After stopping, the oscilloscope no longer performs sampling, and the user can observe the last sampling data retained in the memory. Click the "Run/Stop" button in stop mode to make the oscilloscope enter the running state.

  • Page 12: Generator

    Click the "Menu" button to return to the oscilloscope window. 6.12 Generator Long press the “Run/Stop” button to open the window of the signal generator, The signal amplitude is 2.5V, the maximum frequency of the sine wave is 2MHz, and the other waves are 2MHz.

  • Page 13: Cursor

    6.15 Cursor Hold down the Power button and then click the “s” button to turn on/off the horizontal cursor. Press and hold the Power button and then click the “ns” button to turn on/off the vertical cursor. Press the left and right direction buttons directly to move the horizontal cursor 1 Press and hold the Power button and then press the horizontal direction buttons to move the horizontal cursor 2.

  • Page 14: Trigger

    The difference between peak-to-peak and amplitude(AMP) is shown in the figure above. 7.3 Trigger There are Three options in the trigger menu: “Trigger Mode” / “Trigger Type” and “Trigger level”. Trigger Mode can be selected from "Auto" and "Normal". For “Auto” mode, if a waveform trigger is detected, the waveform signal will be used for triggering.

  • Page 15: Settings

    3. Language selection: Chinese or English. 4. In this menu, long press the "ns" button to enter the usb connection state, long press "s" to change the background color of the measure. Parameters Model DSO1511G Coupling AC/DC Channels AUTO Support Screen size 2.4 inch...

Table of Contents

Save PDF