Subscribe to Our Youtube Channel
Related Manuals for RND power RND 100S-12E
Summary of Contents for RND power RND 100S-12E
- Page 1 U S E R M A N U A L RND 100S-12E RND 100S-24E RND 200S-12E RND 200S-24E PURE SINE WAVE DC TO AC POWER INVERTER...
- Page 2 - P1 -...
- Page 3 - P2 -...
- Page 4 - P3 -...
- Page 5 - P4 -...
- Page 6 - P5 -...
- Page 7 - P6 -...
- Page 8 - P7 -...
- Page 9 - P8 -...
- Page 10 - P9 -...
-
Page 11: Table Of Contents
Sine Wave Inverter Please read this manual carefully before installing and starting up and store it in a safe place. If the device is resold, this instruction manual must be handed over to the purchaser along with the device. Contents 1 Notes on using the instruction manual. -
Page 12: Notes On Using The Instruction Manual
Notes on using the instruction manual Sine Wave Inverter Notes on using the instruction manual Caution! Safety instruction, failure to observe this instruction can cause material damage and impair the function of the device. Supplementary information for operating the device. Caution! Safety instruction relating to a danger from electrical current or voltage. - Page 13 Sine Wave Inverter General safety instructions Use the device only as intended. Do not operate the device in a damp or wet environment. Do not operate the device in areas that are potentially explosive. Maintenance and repair work must only be carried out by qualified per- sonnel who are familiar with the risks involved and the relevant regula- tions.
-
Page 14: Scope Of Delivery
Scope of delivery Sine Wave Inverter Caution! Note the following basic safety information when using electrical devices: – Electric shock – Fire hazard – Injury Operate the device only if you are certain that the housing and the cables are undamaged. Make sure the air inlets and outlets of the device are not covered. -
Page 15: Technical Description
Sine Wave Inverter Technical description 5 Technical description The inverters can be operated wherever there is a 12 V DC supply (RND 100S-12A/E, RND 200S-12A/E) or a 24 V DC supply (RND 100S-24A/E, RND 200S-24A/E). With its low weight and the compact design, the inverter can be easily installed into Camping mobiles, commercial vehicles or motor and sailing yachts. - Page 16 Installing the inverter Sine Wave Inverter For making and testing the electrical connection the following tools are required: Crimping tool 3 different flexible cable connections. The required cable diameter can be taken from the table in the section „Connecting the inverter“ on page Various terminals, multicore cable ends For fixing the inverter you need the following mounting devices: Screws (M4) with spacers and self-locking nuts or sheet metal screws...
-
Page 17: Connecting The Inverter
Sine Wave lnverter Connecting the inverter 6.3 Installing the inverter Adjust the inverter to the chosen installation place and mark the fixing points. Fix the inverter by using the self-chosen fixing method. 7 Connecting the inverter General instructions In case the inverter is installed into vehicles or boats it has to be con- nected to the chassis (ground). -
Page 18: Using The Inverter
Using the inverter Sine Wave lnverter inches of the battery. Connect the positive cable to the red positive terminal. Warning! In order for the integrated residual current-operated protective device of the RND 100S-12A/E, RND 100S-24A/E, RND 200S-12A/E and RND 200S-24A/E inverters to work properly, the earth connection of the inverter (fig. - Page 19 Sine Wave lnverter Using the inverter RND 200S-24A/E), the OVER-LOAD“ LED (fig. 1.3, page 1 / fig. 10.4, page 5) illuminates and an audible signal is given. The inverter shuts down automatically in case of a battery voltage down to 10 V resp. 20 V. If the device overheats, the inverter shuts down –...
-
Page 20: Rectifying Faults
Rectifying faults Sine Wave lnverter Rectifying faults Fault Cause Remedy No output voltage, LED not Bad connection between Check the cables and contact Illuminated battery and inverter. Internal fuses defect. In this case send the unit back to supplier. No output voltage, OVER- The inverter has been over- Switch off the inverter and the TEMP LED illuminates... -
Page 21: Cleaning And Caring For The Inverter
Sine Wave lnverter Cleaning and caring for the inverter Cleaning and caring for the inverter Caution! Do not use sharp or hard objects for cleaning as these may damage the device. Occasionally clean the device with a damp cloth. 11 Guarantee Our general guarantee conditions apply. -
Page 22: Technical Data
Sine Wave lnverter Technical data Technical data RND 100S-12E RND 100S-24E RND 200S-12E RND 200S-24E Item number Rated input voltage 12 V DC 24 V DC 12 V DC 24 V DC 2000 W Constant output power 1000 W Peak output power... - Page 23 902SI200000005...
Need help?
Do you have a question about the RND 100S-12E and is the answer not in the manual?
Questions and answers