Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Erskine Attachments Manuals
  4. Snow Blower
  5. ES2000
  6. Operator's manual

Erskine Attachments ES2000 Operator's Manual

Hydraulic snow blower
Hide thumbs

Advertisement

Quick Links

P/N 320106
Date Printed: 3/29/2019
Erskine Attachments, Inc
Erskine, MN 56535
Printed in U.S.A.
Models ES2000 / ES2400 / ES2400XL
Hydraulic
Snow Blowers
Skid Steer Loaders
Read the Operation & Maintenance Manual entirely. When you see this
symbol, the subsequent instructions and warnings are serious – follow
without exception. Your life and the lives of others depend on it!
for
Operator's Manual
Set-Up Assembly and
Parts Information
D
D
o
o
n
n
o
o
t
t
u
u
s
s
e
e
o
o
r
r
o
o
p
p
e
e
r
r
a
a
t
t
e
e
t
t
h
h
i
i
s
s
m
m
a
a
c
c
h
h
i
i
n
n
e
e
u
u
n
n
manual has been read and understood.
t
t
i
i
l
l
t
t
h
h
i
i
s
s

Advertisement

loading
Need help?

Need help?

Do you have a question about the ES2000 and is the answer not in the manual?

Questions and answers

Related Manuals for Erskine Attachments ES2000

Summary of Contents for Erskine Attachments ES2000

  • Page 1 Models ES2000 / ES2400 / ES2400XL Hydraulic Snow Blowers Skid Steer Loaders Operator’s Manual Set-Up Assembly and Parts Information manual has been read and understood. P/N 320106 Date Printed: 3/29/2019 Erskine Attachments, Inc Erskine, MN 56535 Printed in U.S.A. Read the Operation & Maintenance Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious –...
  • Page 2 Erskine Attachments, Inc. to improve its products whenever it is possible improvements in design or changes in specifications at any time and practical to do so. Erskine Attachments, Inc. reserves the right to make changes and or without notice and without incurring any obligations to install them on add improvements at any time without incurring any obligation to make such changes or add such improvements to products previously sold.

  • Page 3: Table Of Contents

    Write the correct information for YOUR Snow Blower in the spaces below. Always use ____________________________________________________ these numbers when referring to your Snow Blower. ____________________________________________________ Snow Blower Serial Number………….. ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ YOUR ERSKINE ATTACHMENTS DEALER ____________________________________________________ ____________________________________________________ ADDRESS: ____________________________________________________ PHONE: ____________________________________________________ ____________________________________________________ CONTACT:...

  • Page 4: Foreword

    Erskine Attachments, Inc. cannot anticipate every The user is responsible for inspecting the machine possible circumstance that might involve potential daily, and for having parts repaired or replaced hazard.

  • Page 5: Safety

    MODEL ES2000 SNOW BLOWER GENERAL SPECIFICATIONS SAFETY  Whenever you see this symbol, it means Attention! ES2000 x 61” ES2000 x 73” ES2000 x 79” ES2000 x 85” Model ES2000 Become Alert! Your Safety is involved. 61” 73” 79” 85”...

  • Page 6: Serial Number/Decal Location

    SERIAL NUMBER AND SAFETY DECAL LOCATIONS NOTES Serial Number Location: ____________________________________________________ ____________________________________________________ It is important to refer to the serial number of the Snow Blower when making repairs or ordering parts. Early or later models (identification made by serial number) may use different parts, or it may be necessary to use ____________________________________________________ different procedures in doing a specific operation.
  • Page 7 The locations of the safety decals are shown. If these More than one routing may be acceptable decals are missing, damaged, or painted over they depending on the loader. Pick the routing that must be replaced. Call Erskine Attachments, Inc. best suits your loader. (218-687-4045) for replacement decals. PROPER...

  • Page 8: Users Instructions For Mounting The Snowblower

    USERS INSTRUCTIONS FOR MOUNTING THE SNOW BLOWER SET UP ASSEMBLY OF THE SNOW BLOWER After the initial set-up assembly is completed use the following procedure to mount the Erskine™ Snow Blower to the Loader for user operation. Open the rear door. Pull the excess wire harness into the engine compartment.
  • Page 9 SET UP ASSEMBLY OF THE SNOW BLOWER USERS INSTRUCTIONS FOR MOUNTING THE SNOW BLOWER Adjusting the Skid Shoe Height (continued) NOTE: Attachment is shipped with 12FJX (1- 1/16” Female JIC Swivel) fittings on the ends of the lead hoses. ES2400 & ES2400XL 7.

  • Page 10: Operating The Snowblower

    Pistol Grip Control Harness. Stop the engine and exit the Loader. NOTE: Your Loader must have the attachment ES2000 control kit installed to make use of the lever switches. Remove the lynch pin (1) on the skid shoes.
  • Page 11 SET UP ASSEMBLY OF THE SNOW BLOWER OPERATING THE SNOW BLOWER DISCHARGE CHUTE INSTALLATION Remove one of the roller guides from the blower housing by removing the bolt securing The previously installed Pistol Grip allows the the roller guide. operator to engage all chute functions. (see Set Up Assembly) FUNCTIONS ARE ACTIVATED AS FOLLOWS: (A) Button 1 moves deflector UP.

  • Page 12: Routine Maintenance

    ROUTINE SNOW BLOWER MAINTENANCE SET UP ASSEMBLY OF THE SNOW BLOWER It is the operator’s responsibility to make daily inspections of the loader and attachment for damage, loose bolts, fluid CRATE REMOVAL AND ASSEMBLY leaks, or anything else that could cause a potential service or safety problem. Preventive maintenance is the easiest and least expensive type of maintenance.
  • Page 13 WIRE HARNESS PARTS INFORMATION ROUTINE SNOW BLOWER MAINTENANCE LUBRICATION (continued) Grease the auger drive after every 4 hours of operation. NOTE: There are (2) grease fittings, one on each side of the auger tube. Grease the (3) chute roller guide bushings also after every 4 hours of operation.
  • Page 14 ROUTINE SNOW BLOWER MAINTENANCE HYDRAULIC ASSEMBLY AUGER REMOVAL AND INSTALLATION REF. PART NO. DESCRIPTION QTY. 1. Loosen the setscrew on the bearing HOSE – 1/4" x 53” 6MB-2MP upper deflector……………… 1 315093 eccentric locking collar. Using a hammer ADAPTER - elbow 2MP-2FPX90 ………………………….. 1 103284 and punch, rotate the collar in the opposite CYLINDER –...

  • Page 15: Parts Information

    PARTS INFORMATION ROUTINE SNOW BLOWER MAINTENANCE AUGER REMOVAL AND INSTALLATION (continued) 4. Slide the auger straight forward and out of the blower body. 5. The hydraulic motor and housing can now be removed from the auger. 6. To install, use reverse procedure. 7.
  • Page 16 ROUTINE SNOW BLOWER MAINTENANCE ES2400/ES2400XL DRIVE ASSEMBLY FAN REMOVAL AND INSTALLATION REF. PART NO. DESCRIPTION QTY. The auger must be removed first. (see Auger AUGER - 18” diameter x 60” ………………………………… 1 315342 Removal page 15) Block AUGER - 18” diameter x 72” ………………………………… 1 315202 AUGER - 18”...
  • Page 17 PARTS INFORMATION ES2400/ES2400XL NOTES ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ -24- -17-...
  • Page 18 PARTS INFORMATION ES2000 ES2000 DRIVE ASSEMBLY REF. PART NO. DESCRIPTION QTY. AUGER - 16” diameter x 61” ………………………………… 1 315404 AUGER - 16” diameter x 73” ………………………………… 1 315405 AUGER - 16” diameter x 79” ………………………………… 1 315406 AUGER - 16” diameter x 85” ………………………………… 1 315447 BEARING ASSEMBLY - 1-1/4”...
  • Page 19 CUTTING EDGE – 1/2 x 4 x 77” bolt-on ………………… 1 200132 CUTTING EDGE – 1/2 x 4 x 83” bolt –on ………………. 1 104038 SKID SHOE ES2000 - assembly (includes lynch pin)….. 2 100301 BOLT - 5/8 x 1-1/2 NF gr8………………………………… 8 WASHER – lock 5/8 high alloy.……………………………. 8 33897 NUT - 5/8 NF gr8..…………………………………………..
  • Page 20 PARTS INFORMATION ES2400/ES2400XL ES2400/ES2400XL BODY ASSEMBLY REF. PART NO. DESCRIPTION QTY. HINGE PIN - deflector..........…..… 1 315124 PIN - cotter…………………………………………………….. 1 BOLT - 1/2 x 1-1/2 NC gr5…………………………………… 2 NUT - lock 1/2 NC…………………………………………….. (20)60” (22)72” (24)84” DEFLECTOR - chute ………………………………………… 1 315067 CHUTE..............…..

This manual is also suitable for:

Es2400Es2400xl
Save PDF