Subscribe to Our Youtube Channel
Related Manuals for Erskine Attachments Mini Snow Blade
Summary of Contents for Erskine Attachments Mini Snow Blade
- Page 1 Mini Snow Blade Mini Skid Steer Loaders Mini Track Loaders Operator’s Manual Maintenance Parts Information Read this Manual Before Use...
-
Page 2: Table Of Contents
Serial Number………….._____________ YOUR ATTACHMENT DEALER ADDRESS: PHONE: CONTACT: NOTE: Erskine Attachments LLC reserves the right to make improvements in design or changes in specifications at any time without notice and without incurring any obligations to install them on units previously sold. -
Page 3: Safety
Indicates potentially Erskine Attachments LLC cannot anticipate every hazardous situation which, if not avoided, possible circumstance that might involve potential will result in death or serious injury. hazard. The safety messages found in this manual and on the machine are therefore not all inclusive. - Page 4 Wear • Do not modify equipment or add attachments that protective gloves and safety glasses or goggles are not approved by Erskine Attachments LLC. when servicing or performing maintenance on hydraulic systems. • Use adequate safety warning lights and devices as required by local regulations.
-
Page 5: Serial Number/Decal Location
SERIAL NUMBER AND SAFETY DECAL LOCATIONS Serial Number Location: It is important to refer to the serial number of the attachment when making repairs or ordering parts. Early or later models (identification made by serial number) may use different parts, or it may be necessary to use different procedures in doing a specific operation. - Page 6 Safety Decals Locations: Location: On back of moldboard, centered The locations of the safety decals are shown. If these decals are missing, damaged, or painted over Quantity: 1 they must be replaced. Call Erskine Attachments LLC (218-435-4045) for replacement decals.
-
Page 7: User's Mounting Instructions
USER’S MOUNTING INSTRUCTIONS After the initial set-up assembly is completed, use the following procedure to mount the attachment to the loader. Coupler wedges or pins must extend through holes in attachment. Levers must be fully down and locked. Failure to secure wedges or pins can allow the attachment to come off and cause injury or death. - Page 8 USER’S MOUNTING INSTRUCTIONS Connecting Hydraulics: 1. If the mini snow blade is equipped with the optional hydraulic angle package, connect the hydraulic quick couplers from the attachment to the loader. IMPORTANT: Wipe the ends of the hydraulic quick couplers (both lead and loader) with a rag to...
-
Page 9: Operating Instructions
Trip Springs The mini snow blade is equipped with trip springs that Trip Spring allow the moldboard to tilt forward when the cutting edge strikes an obstruction. This helps protect the attachment and the obstruction from damage. - Page 10 OPERATING INSTRUCTIONS Light Material Removal Trip Locks The mini snow blade may be used for light material grading. In order to use the attachment for this purpose, install bolts and lock nuts in both of the trip locks to lock the moldboard in the upright position.
-
Page 11: Routine Maintenance
ROUTINE MAINTENANCE Lower the attachment to rest flat on the ground, shut down the engine, relieve the hydraulic pressure to the attachment, set the park brake, and wait for all motion to stop before leaving the operator’s seat to perform service of any kind. It is the operator’s responsibility to make daily inspections of the loader and attachment for damage, loose bolts, fluid leaks, or anything else that could cause a potential service or safety problem. -
Page 12: Parts Information
PARTS INFORMATION ITEM QTY PART NO. DESCRIPTION STOCK NO. 400103 MOUNT W/A 400108 SNOW BLADE SWIVEL W/A 400109 MOLDBOARD 48 W/A 48” SNOWBLADE 400110 MOLDBOARD 60 W/A 60” SNOWBLADE 400111 CUTTING EDGE 1/2 X 4 X 49.5 BOLT ON 48” SNOWBLADE 400186 CUTTING EDGE 1/2 X 4 X 61.5 BOLT ON 60”... - Page 13 PARTS INFORMATION...
- Page 14 PARTS INFORMATION ITEM PART NO. DESCRIPTION STOCK NO. 400074 CYLINDER 2 X 4 W/BUSHINGS HYDRAULIC OPTION ONLY 34.1 300404 ADPT STR 8MB-6MJ ORFICE .030 HYDRAULIC OPTION ONLY 34.2 201925 ADPT STR 8MB-6MJ HYDRAULIC OPTION ONLY 34.3 400047 HOSE 3/8 X 65" 8FJX-6FJX HYDRAULIC OPTION ONLY...
-
Page 15: General Specifications
GENERAL SPECIFICATIONS Model Working Width – Straight 49.5” 61.5” Working Width – Fully Angled 44” @ 27° 54.5” @ 27° 21.3” Overall Height Trip Type Moldboard Number of Trip Springs 1/2" x 4” Bolt-On Cutting Edge Operating Weight (w/out mount) 175 lbs. -
Page 16: Bolt Torque Information
BOLT TORQUE INFORMATION... -
Page 17: Notes
NOTES ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________... - Page 18 NOTES ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________...
-
Page 19: Warranty
Erskine Attachments LLC to improve its products whenever it is possible and practical to do so. Erskine Attachments LLC reserves the right to make changes and or add improvements at any time without incurring any obligation to make such changes or add such improvements to products previously sold. - Page 20 P/N 300439 Date Printed: 2/22/2021 Printed in U.S.A. Erskine Attachments LLC...
Need help?
Do you have a question about the Mini Snow Blade and is the answer not in the manual?
Questions and answers