Table of Contents
Advertisement
1.6 Setting Board Address (Software - System Relay)
When using tracker expansion boards connected to a single access control system, the board addresses on EACH tracker expansion board
should be set so that the Remote Account Manager for Windows (V 6.4 or newer only) software can identify each tracker expansion
board. The software reserves board address 0, 1 and 2 for the access control system. Tracker expansion board address starts with relay
address 3 (see below).
IMPORTANT:
"Zone" Addresses:
Board addresses can be set the same (functions as "zones"), but the system's "tracking" capability will NOT be able
to distinguish SPECIFIC access point activity. Two or more boards with the same board address will be tracked and logged as "zone number"
but not a specific location for that activity. For example, if you have 4 card readers in different locations in a building, and all have the same
board addresses, the software would track that a card reader in the "zone number" was used, but not which specific location it was used.
Zones can be used for a restricted area with multiple entrances inside the complex such as a pool area/tennis courts or community center.
Zones are not recommended if detailed tracker activity reports are required.
BOARD ADDRESS
ON
1
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Board addresses 3 thru 10 MUST connect to Relay 2/Wiegand 2 on the access control system
Maximum HARD wire run between tracker expansion boards (up to 24 boards) is 4000 feet TOTAL,
BOARD ADDRESS
BOARD ADDRESS
ON
ON
1
1
0
0
OFF
OFF
Board Address 3
Board Address 4
System Relay 3
System Relay 4
Note: Start at board address 3, the software reserves board address (system relay) 0, 1 and 2 for the access control system ONLY.
Board addresses 11 thru 18 MUST connect to Relay 1/Wiegand 1 on the access control system
Maximum HARD wire run between tracker expansion boards (up to 24 boards) is 4000 feet TOTAL,
BOARD ADDRESS
BOARD ADDRESS
ON
ON
1
1
0
0
OFF
OFF
Board Address 11
Board Address 12
System Relay 11
System Relay 12
6
The software uses the board address number for the System Relay number.
RF
OUTPUT
ALARM
AUX
SECURE
RF
RF
CODE
CODE
CODE
RELAY
RELAY
RELAY
DATA
STATUS
SENT
GOOD
BAD
NC
NC
NC
NO
NO
NO
RESET
ENT
see section 2 for more information about HARDwiring limitations.
BOARD ADDRESS
BOARD ADDRESS
ON
ON
1
1
0
0
OFF
OFF
Board Address 5
Board Address 6
System Relay 5
System Relay 6
see section 2 for more information about HARDwiring limitations.
BOARD ADDRESS
BOARD ADDRESS
ON
ON
1
1
0
0
OFF
OFF
Board Address 13
Board Address 14
System Relay 13
System Relay 14
2358-010
21
Switch MUST be ON (1) for
22
board addresses 10 thru 18.
23
(Dial number +10).
24
25
Switch MUST be OFF (0) for
26
board addresses 3 thru 9.
27
(Dial number only).
28
29
30
31
IMPORTANT:
ONLY 8
32
board addresses can
33
be used for EACH
34
wiegand/relay run.
IMPORTANT:
DO NOT
set the board address
to 0, 1, 2 or 19.
BOARD ADDRESS
BOARD ADDRESS
ON
ON
1
1
0
0
OFF
OFF
Board Address 7
Board Address 8
System Relay 7
System Relay 8
BOARD ADDRESS
BOARD ADDRESS
ON
ON
1
1
0
0
OFF
OFF
Board Address 15
Board Address 16
System Relay 15
System Relay 16
Note: Board Addresses 0, 1, 2 & 19 will not generate a wiegand signal.
BOARD ADDRESS
ON
1
0
OFF
Switch
Dial Numbers
Set dial numbers
accordingly with switch.
Example: The switch is OFF and
the dial is set to 3, so the Board
Address is 3. The software uses
the board address as the System
Relay, this means the System
Relay for this board is 3. See
below for all board settings.
BOARD ADDRESS
BOARD ADDRESS
ON
ON
1
1
0
0
OFF
OFF
Board Address 9
Board Address 10
System Relay 9
System Relay 10
BOARD ADDRESS
BOARD ADDRESS
ON
ON
1
1
0
0
OFF
OFF
Board Address 17
Board Address 18
System Relay 17
System Relay 18
2358-065 Issued 7-19
Version E
Advertisement
Table of Contents
