GDC SR-1000 Installation Manual
  1. Manuals
  2. Brands
  3. GDC Manuals
  4. Control Systems
  5. SR-1000 STANDALONE INTEGRATED MEDIA BLOCK
  6. Installation manual

GDC SR-1000 Installation Manual

Integrated media block™ with s1 kit plus
Hide thumbs Also See for SR-1000:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLATION MANUAL FOR
SR-1000 INTEGRATED MEDIA BLOCK™ WITH S1 KIT PLUS
(For use with Series 1 Projectors)
Version 7.90
th
February 15
, 2023

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SR-1000 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for GDC SR-1000

Summary of Contents for GDC SR-1000

  • Page 1 INSTALLATION MANUAL FOR SR-1000 INTEGRATED MEDIA BLOCK™ WITH S1 KIT PLUS (For use with Series 1 Projectors) Version 7.90 February 15 , 2023...

  • Page 2: Table Of Contents

    Installing the HDDs ................8 Installing the SR-1000 IMB ............10 Connecting the IMB to a Series 1 Projector ......... 17 Powering up the SR-1000 IMB with S1 Kit Plus ......18 Projector Configuration in SDI Mode ........19 Supported Playback Formats ..........20 Converting SR-1000 from SDI Mode to IMB Mode ....
  • Page 3 To ensure proper operation and to maximize value of the SR-1000 Integrated Media Block™ with S1 Kit Plus, please review this Installation Manual. It will guide you through all the features and benefits of the new SR-1000 Integrated Media Block™ with S1 Kit Plus.
  • Page 4 CONTACTS AND OFFICES CONTACTS AND OFFICES Website Contact Us Worldwide Offices 24/7 Support - 3 - February 15 , 2023 GDC SR-1000 INTEGRATED MEDIA BLOCK™ WITH S1 KIT PLUS INSTALLATION MANUAL...

  • Page 5: Introduction

    Series 1 DLP Cinema Projector. It consists of a metal chassis (as shown in Figure 1) and the SR-1000 IMB with its faceplate (as shown in Figure 2). The faceplate has two BNC connectors for HD-SDI connections to a Series 1 Projector.

  • Page 6: Physical, Environmental And Power Requirements

    ▪ Operating Altitude – 10,000ft. (3,000m) above sea level ▪ • Power: Input – 100 to 240V, 63 to 47Hz, 2/4.5A ▪ - 5 - February 15 , 2023 GDC SR-1000 INTEGRATED MEDIA BLOCK™ WITH S1 KIT PLUS INSTALLATION MANUAL...

  • Page 7: Packing List

    2. Packing List 2 Packing List Contents of the SR-1000 IMB with S1 Kit Plus package are as listed below: Sr.No. Description Quantity Actual Photograph Metal Chassis SR-1000 IMB 3.5” SATA HDD with HDD Tray eSATA Cable (1M, Male-to-Male) Coaxial Cables...
  • Page 8 RJ45 to DB25 Audio Converter Cable Holder Clip for eSATA Spare Screws for Front Plate (2 nos.) Subject to actual configuration. Please specify with GDC sales representative. - 7 - February 15 , 2023 GDC SR-1000 INTEGRATED MEDIA BLOCK™ WITH S1 KIT PLUS...

  • Page 9: Hardware Installation And Setup

    3.1 Installing the HDDs The front panel of the S1 Kit Plus chassis houses the slot for the SR-1000 IMB along with the RAID bay slots for HDDs, LED indicator array (for the RAID, Fan and Power) and a Power switch, as shown in Figure 3.
  • Page 10 Insert the Tray Key into the key slot of the HDD Tray and turn it counter-clockwise to lock the HDD tray in place, as shown in Figure 6. Figure 6: Lock HDD using Tray Key - 9 - February 15 , 2023 GDC SR-1000 INTEGRATED MEDIA BLOCK™ WITH S1 KIT PLUS INSTALLATION MANUAL...

  • Page 11: Installing The Sr-1000 Imb

    3. Hardware Installation and Setup 3.2 Installing the SR-1000 IMB Before inserting the SR-1000 IMB into the metal chassis, remove the dummy cover plate from the front panel of the chassis (refer to Figure 7). Use a phillips-head screwdriver to remove the screws on either side of the cover plate, as shown in Figure 8.
  • Page 12 Figure 9: Affix Cover Plate to Chassis Insert the SR-1000 into the IMB slot of the metal chassis. While doing this, it is essential to properly align the IMB against the side railings of the metal chassis, which have been highlighted in Figure 10.
  • Page 13 3. Hardware Installation and Setup Figure 11: Insert IMB into chassis After inserting the SR-1000 , fasten the two screws on either side of the IMB faceplate using a Phillips-head screwdriver (as shown in Figure 12). Figure 12: Tighten screws on IMB faceplate Figure 13 shows the S1 Kit Plus chassis with the SR-1000 IMB and HDDs installed.
  • Page 14 3. Hardware Installation and Setup Figure 13: S1 Kit Plus with SR-1000 IMB and HDDs installed Peel-off the protective paper on the back of the cable holder clips, as shown in Figure 14. Figure 14: Remove protective paper from cable holder clip Attach one of the clips to the bottom-left corner of the chassis top panel and ensure that the cable slot on the clip is aligned in the front-back direction, as indicated in Figure 15.
  • Page 15 Note: The cable holder clips are made of soft rubber material. So, the eSATA cable can easily be inserted into them, by gently pressing it into the cable slot on the clip. - 14 - February 15 , 2023 GDC SR-1000 INTEGRATED MEDIA BLOCK™ WITH S1 KIT PLUS INSTALLATION MANUAL...
  • Page 16 Figure 18: Insert eSATA cable into Clips Connect the other end of the eSATA cable to the eSATA port on the SR-1000 IMB (as shown in Figure 19). Secure the cable by tightening the attached screw, using a flat-head screwdriver.
  • Page 17 Figure 21. Connect the plug at the other end of the power cord to a recommended power outlet. Figure 21: Back panel connections for Power Cord - 16 - February 15 , 2023 GDC SR-1000 INTEGRATED MEDIA BLOCK™ WITH S1 KIT PLUS INSTALLATION MANUAL...

  • Page 18: Connecting The Imb To A Series 1 Projector

    Configure the ETH1/ETH2 IP address from the Web UI interface under the Configuration → System → Network Configuration section. Note: The SR-1000 ETH1/ETH2 IP Address should belong to the same subnet as the Projector’s IP Address. Figure 22: Cable Connections on the SR-1000 IMB Figure 23: HD-SDI Cables connected to Link Decryptor Board of Series 1 Projector For more information regarding the SR-1000’s network and storage setup, please refer to the...

  • Page 19: Powering Up The Sr-1000 Imb With S1 Kit Plus

    Switch the Power button on the front panel of the S1 Kit Plus chassis to ON position. Once the IMB boots up, the Web UI interface of the SR-1000 can be accessed from a laptop/PC connected to the SR-1000 ETH1/ETH2 network. For more details regarding how to access the SR-1000 Web UI interface, please refer to the SR-1000 User Manual.

  • Page 20: Projector Configuration In Sdi Mode

    Set the correct macro (video input to Projector is 'SDI') on the Projector and turn on the lamp. On the SR-1000 Web UI, load a playlist and start the playback to check if content can be played successfully. For more details regarding this, please refer to the GDC SR-1000 User Manual.

  • Page 21: Supported Playback Formats

    6 Converting SR-1000 from SDI Mode to IMB Mode It is possible to convert a SR-1000 in S1 mode to IMB mode, so that it be used with Series 2, Series 3 or Series 4 Projectors. Please contact your nearest GDC Regional Office for more information regarding how this conversion can be done.
  • Page 22 GDC Technology manufacturing facility is ISO 9001:2015 certified. Copyright © 2023 GDC Technology Limited. All Rights Reserved. All trademarks listed in this manual are properties of their respective owners. Specifications are subject to change without notice due to ongoing product development and improvement.

Table of Contents