Program Change - Roland SD-90 Midi Implementation Manual

MIDI Implementation
Cutoff (Controller number 74)
Status 2nd byte
BnH 4AH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Cutoff value (relative change):00H - 7FH (-64 - 0 - +63)
Decay Time (Controller number 75)
Status 2nd byte
BnH 4BH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Decay Time value (relative change):00H - 7FH (-64 - 0 - +63)
Vibrato Rate (Controller number 76)
Status 2nd byte
BnH 4CH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Vibrato Rate value (relative change):00H - 7FH (-64 - 0 - +63)
Vibrato Depth (Controller number 77)
Status 2nd byte
BnH 4DH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Vibrato Depth Value (relative change):00H - 7FH (-64 - 0 - +63)
Vibrato Delay (Controller number 78)
Status 2nd byte
BnH 4EH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Vibrato Delay value (relative change):00H - 7FH (-64 - 0 - +63)
General Purpose Controller 5 (Controller number 80)
Status 2nd byte
BnH 50H
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* The Tone Level parameter (PATCH/TONE) of Tone 1 will change.
General Purpose Controller 6 (Controller number 81)
Status 2nd byte
BnH 51H
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* The Tone Level parameter (PATCH/TONE) of Tone 2 will change.
General Purpose Controller 7 (Controller number 82)
Status 2nd byte
BnH 52H
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* The Tone Level parameter (PATCH/TONE) of Tone 3 will change.
General Purpose Controller 8 (Controller number 83)
Status 2nd byte
BnH 53H
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* The Tone Level parameter (PATCH/TONE) of Tone 4 will change.
Portamento control (Controller number 84)
Status 2nd byte
BnH 54H
n = MIDI channel number:0H - FH (Ch.1 - 16)
kk = source note number:00H - 7FH (0 - 127)
* A Note-on received immediately after a Portamento Control message will change
continuously in pitch, starting from the pitch of the Source Note Number.
* If a voice is already sounding for a note number identical to the Source Note Number,
this voice will continue sounding (i.e., legato) and will, when the next Note-on is
received, smoothly change to the pitch of that Note-on.
* The rate of the pitch change caused by Portamento Control is determined by the
Portamento Time value.
2
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
kkH
Effect 1 (Reverb Send Level) (Controller number 91)
Status 2nd byte
BnH 5BH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Reverb Send Level:00H - 7FH (0 - 127)
Effect 3 (Chorus Send Level) (Controller number 93)
Status 2nd byte
BnH 5DH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Chorus Send Level:00H - 7FH (0 - 127)
RPN MSB/LSB (Controller number 100, 101)
Status 2nd byte
BnH 65H
BnH 64H
n = MIDI channel number:0H - FH (Ch.1 - 16)
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are extended
When using RPNs, first the RPN (Controller numbers 100 and 101; they can be sent in any
This device receives the following RPNs.
RPN Data entry
MSB, LSB MSB, LSB
00H, 00H mmH, llH
mm:
ll:
Up to 2 octave can be specified in semitone steps.
00H, 01H mmH, llH
mm, ll:
00H, 02H mmH, llH
mm:
ll:
7FH, 7FH ---, ---
RPN and NRPN will be set as "unspecified". Once this setting has been
made, subsequent
Parameter values that were previously set will not change.
mm, ll: ignored

Program Change

Status 2nd byte
CnH ppH
n = MIDI channel number:0H - FH (Ch.1 - 16)
pp = Program number:00H - 7FH (prog.1 - prog.128)
Channel Pressure
Status 2nd byte
DnH vvH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Channel Pressure:00H - 7FH (0 - 127)
Pitch Bend Change
Status 2nd byte
EnH llH
n = MIDI channel number:0H - FH (Ch.1 - 16)
mm, ll = Pitch Bend value:00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
3rd byte
vvH
Default Value = 28H (40)
3rd byte
vvH
Default Value = 00H (0)
3rd byte
mmH
llH
Notes
Pitch Bend Sensitivity
00H - 18H (0 - 24 semitones)
ignored (processed as 00H)
Master Fine Tuning
20 00H - 40 00H - 60 00H (-8192 - 50/ 8192 - 0 -
+8192*50/8192 cent)
Master Coarse Tuning
10H - 40H - 70H (-48 - 0 - +48 semitones)
ignored (processed as 00H)
RPN null
3rd byte
mmH