Philips 4000 Series User Manual page 2

25BDL4050I
Safety Instructions
Warnings and Precautions
KNOW THESE SAFETY SYMBOLS
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
This symbol indicates high voltage is present inside.
It is dangerous to make any kind of contact with any
inside part of this product.
The electronic paper screen is composed of plastic
film and ultra-thin glass, which is different from the
LCD screen normally used. It cannot withstand any
external impact, such as single-point or heavy object
pressure, which may cause damage or breakage of
the screen; please pay special attention to its use.
The warranty does not cover screen breakage.
This symbol alerts you that important literature
concerning operation and maintenance has been
included with this product.
CAUTION:
FCC/CSA regulations state that any
unauthorized changes or modifications to this
equipment may void the user's authority to
operate it.
CAUTION:
To prevent electric shock, match the wide blade
of plug to the wide slot, and fully insert the
plug.
TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR
ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
The Socket-outlet should be installed near the apparatus and
be easily accessible.
Read and follow these instructions when
connecting and using your ePaper display:
• Unplug the display if you are not going to use it for an
extensive period of time.
• Unplug the display if you need to clean it with a slightly
damp cloth. The screen many be wiped with a dry cloth
when the power is off. However, never use alcohol,
solvents or ammonia-based liquids.
• Consult a service technician if the display does not operate
normally when you have followed the instructions in this
manual.
• The casing cover should be opened only by qualified
service personnel.
• Keep the display out of direct sunlight and away from
stoves or any other heat sources.
• Keep the display away from oil, otherwise the plastic
cover may be damaged.
• Remove any object that could fall into the vents or
prevent proper cooling of the display's electronics.
• Keep the display dry. To avoid electric shock, do not
expose it to rain or excessive moisture.
• If turning off the display by detaching the power cable,
wait for 6 seconds before re-attaching the power cable
for normal operation.
• To avoid the risk of shock or permanent damage to
the set do not expose the display to rain or excessive
moisture.
• When positioning the display, make sure the power plug
and outlet are easily accessible.
• The Class I apparatus shall be connected to a mains socket
outlet with a protective earthing connection.
• IMPORTANT: Always activate a screen saver program
during your application. If a still image in high contrast
remains on the screen for an extended period of time, it
may leave an 'after-image' or 'ghost image' on the front
of the screen. This is a well-known phenomenon that is
caused by the shortcomings inherent in Microcapsule
technology. In most cases the afterimage will disappear
gradually over a period of time after the power has been
switched off. Be aware that the after-image symptom
cannot be repaired and is not covered under warranty.
Environmental absolute ratings
Item
Storage temperature
Operation temperature
Glass Surface temperature
(Operation)
Storage humidity
Operating humidity
• Please confirm that the power distribution system
installed in the building provides a circuit breaker for a
rated voltage of 120/240V and a maximum of 20A.
• If provided with a 3-pin attachment plug on the power
cord, plug the cord into a grounded (earthed) 3-pin
outlet. Do not disable the power cord grounding pin, for
example, by attaching a 2-pin adapter. The grounding pin
is an important safety feature.
• Stability Hazard.
The device may fall, causing serious personal injury or
death. To prevent injury, this device must be securely
attached to the floor/wall in accordance with the
installation instructions.
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Read all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Install in accordance with the manufacturer's instructions.
ii
Min. Max. Unit
-25 60 °C
15 35 °C
0 65 °C
5 95 % RH
20 80 % RH