Advertisement
Available languages
Available languages
To Fit And Use Your
A
A
B
B
Splashguard
K
K
L
L
Refer to Illustrations
1
Raise the mixer head until it locks.
2
Fit the bowl onto the base.
U
U
V
V
3
Push the splashguard onto the
underside of the mixer head until fully
located. The hinged section should be
positioned as shown.
4
Insert required tool.
5
Lower the mixer head.
During mixing, ingredients can be
l
added directly to the bowl via the
hinged section of the splashguard.
You do not need to remove the
l
splashguard to change tools.
6
Remove the splashguard by raising
the mixer head and pushing it down.
A
B
C
D
Tool Adjustment
K
L
M
N
Refer to Illustrations
K-beater & Whisk
The tools are set to the correct height
U
V
W
X
for the bowl supplied in the factory and
should not require adjustment.
However, if you wish to adjust the tool
use a suitable sized spanner:
TYPE KVC85 = 15mm
TYPE KVL85 = 19mm
Then follow the instructions below:
1
Unplug the appliance.
2
Raise the mixer head and insert the
whisk or beater.
3
Lower the mixer head. If the
clearance needs to be adjusted,
raise the mixer head and remove the
tool. Ideally the whisk and K-beater
should be almost touching the
bottom of the bowl.
4
Using a suitable spanner loosen the
nut sufficiently to allow adjustment
of the shaft. To lower the tool closer
to the bottom of the bowl, turn the
shaft anti-clockwise. To raise the tool
away from the bottom of the bowl
turn the shaft clockwise.
C
C
D
D
E
E
F
F
M
M
N
N
O
O
P
P
–
W
W
X
X
Y
Y
Z
Z
E
F
G
H
O
P
Q
R
Y
Z
5
Re-tighten the nut.
G
G
H
H
I
I
J
J
6
Fit the tool to the mixer and lower
the mixer head. (Check its position
Q
Q
R
R
S
S
T
T
see points above).
7
Repeat the above steps as necessary
until the tool is set correctly. Once
this is acheived tighten the nut
securely.
Note: Spanner shown is for
l
illustration purpose only.
Dough Tool
This tool is set at the factory and should
require no adjustment.
To Fit and Remove Head
A
B
C
D
Cover
K
L
M
N
Refer to Illustrations
I
J
1
Remove the slow speed and high
speed outlet covers.
U
V
W
X
2
With the retention clip pressed in, lift
S
T
up the head cover and slide forward.
3
To fit an alternate head cover, insert
the pegs on the end of the head
cover into the two holes on the slow
speed outlet.
4
Whilst pressing the retention clip,
push the head cover down into place
on the mixer head.
5
Replace slow speed and high speed
A
outlet covers.
To Assemble The Creaming
K
Beater
U
Refer to Illustrations
Fitting The Wiper Blade
The wiper blade is supplied already
l
fitted and should always be removed
before cleaning.
1
Carefully fit the flexible wiper blade
onto the tool by locating the base
of the wiper blade into the slot then
fit one side into the groove before
gently hooking the end in place.
Repeat with the other side.
10
A
B
K
L
E
F
G
H
O
P
U
Q
V
R
–
Y
Z
B
A
C
B
D
C
E
D
L
K
M
L
N
M
O
N
V
U
W
V
W
X
Y
X
–
C
D
E
M
N
O
I
J
W
S
X
T
Y
F
E
G
F
H
G
P
O
Q
P
R
Q
Z
Y
Z
Advertisement
