Waterway CLEARWATER II - Water Filtration System Manual

Waterway CLEARWATER II - Water Filtration System Manual

Also See for CLEARWATER II:

Advertisement

Waterway CLEARWATER II - Water Filtration System Manual

CLEARWATER II D.E. FILTER SYSTEM OWNER'S MANUAL

Our ClearWater II D.E. Filter System is shipped from Waterway complete with everything you need right in the box. Assemble filter system only after above-ground pool is installed. Fill pool with water. Do not raise water level above pool return line.

The pool equipment should be located between pool skimmer and return line. The filtration system should not be closer than 2 ft. and not further than 5 ft. from the pool. The ClearWater II D.E. Filter System needs to be on a completely flat surface (e.g. patio block, cement slab, etc.). The pump will require a 110 volt/20 amp service.


A GFCI is required. Follow national and local building and safety codes.

Before opening shipping carton, make sure box is in the upright position. Inside the carton, you will find:

  1. One base
  2. One pump (packaged in separate box)
  3. One filter
  4. Two lengths of 6 ft. hose
  5. One bag with fittings

INSTALLATION INSTRUCTIONS


READ ALL INSTRUCTIONS AND WARNING LABELS BEFORE OPERATING FILTER!

  1. Place filter and base on a level, secure surface. Place the pump on the base to the left of the filter. The pump should now be facing the filter marked "Inlet". There is no need to disassemble filter or pump assemblies.
  2. Open pump trap lid and remove 2" gasket. Place 2" gasket into union nut. Hand tighten union nut to suction side of pump (Detail 5).
  3. Secure pump to the base using the pin & anchor assemblies (Detail 4).
  4. Open fittings bag and remove coupling assembly (Detail 2). Assemble 2" gasket, coupling, coupling O-Ring, and 2" union nut, and thread into inlet side of filter.
    INSTALLATION INSTRUCTIONS
  5. Thread 2" union nut to pump discharge (Detail 3). Thread hose adapter with O-Ring, to pump trap suction side (Detail 1).
  6. From the fittings package, remove 11/2" hose adapter and O-ring
  7. Remove 4 hose clamps from the fittings bag. Select one of the hose lengths and slip one clamp over the end of hose adapter. Place the end of the hose on to the hose adapter (pump suction) and the other end to the hose adapter end of the pool skimmer. Repeat steps with filter outlet to pool return.
  8. Remove the Lid Handle, #1, from the fittings bag and attach it to the top of the Lid Assembly, #12, as shown (Detail 6). Secure ClearWater Filter to ClearWater Filter Base using #24a Phillips Head Screws (2) (Detail 6a & 6aa). Fill pool until water level is halfway up length of skimmer throat.


  9. Open air release knob. Plug in and turn on pump. Air will pass out of the filter through the air release knob. Once water discharges from knob, close it.
    NOTE: To remove Lid Assembly, take off Filter Nut, #3, insert Filter Wrench, #20a, in notch between Filter Body, #20 and Lid Assembly, #12, twist and separate as shown in Detail 6a.

CLEARWATER II D.E. FILTER SYSTEM REPLACEMENT PARTS

REPLACEMENT PARTS

Item Part No. Description
1 519-7601 Lid Handle
2 819-9002 #12 x 3/4" S/S Phillips Head Screw
3 718-7251 Filter Locknut Assembly
4 602-0200 Air Relief Plug
5 805-0207 O-Ring - Air Relief
6 830-4000SS Pressure Gauge
7 519-7451 Handle Assembly (2)
8 805-0224 O-Ring - Air Relief
9 519-7430 Gauge - Fitting Adapter
10 805-0117SD O-Ring - Adapter
11 805-0117SD 805-0460 Lid O-Ring
12
519-7411 Lid Assembly (Small)
519-7401 Lid Assembly (Large)
13 519-7441 Wing-Nut
14 500-7310 Screen/Sock Assembly
15 718-7210 Tie Nut - D.E.
16 419-7241 Plug - 2" x 1 1/2" MPT
17 519-7269 Locator - Top Grids - D.E.
18
550-7210 D.E. Grids - 12 sq. ft. (7)
550-7220 D.E. Grids - 18 sq. ft. (7)
19 550-7100 Base Assembly - 12 sq. ft.
550-7120 Base Assembly - 18 sq. ft.
20 515-7251 Filter Body Bottom
20a 519-7470 Filter Wrench (see Detail 6a)
21 805-0224 O-Ring (4) 1 1/2" MPT x 1 1/2" Male Smooth
22 417-6241 1 1/2" MPT x 1 1/2" Male Smooth Hose Adapter (2)
23 500-5300 Drain Assembly
24 672-7401 ClearWater II Base
24a 819-0044 #10 x 1" S/S Phillips Head Screw (2)
25 415-5001 2" Union Nut
26 419-7241 Coupling
27 711-4010 2" Union Gasket (2)
28 429-7221 Snap Pin (4)
29



PH1100 1 HP - 1-Speed Hi-Flo Pump
PH1150 1 1/2 HP - 1-Speed Hi-Flo Pump
PH1200 PH2100 2 HP - 1-Speed Hi-Flo Pump 1 HP - 2-Speed Hi-Flo Pump
PH2150 1 1/2 HP - 2-Speed Hi-Flo Pump
PH2200 2 HP - 2-Speed Hi-Flo Pump
30 310-6500 6" Trap - 1 1/2" Buttress x 2" Flange
31 319-3230 6" Basket Assembly
32 805-0436 O-Ring
33 319-3260 6" Trap Lid

CLEANING INSTRUCTIONS

If the pressure gauge on your filter reads 5 PSI or higher than the original starting pressure, the filter needs to be cleaned. The ClearWater II D.E. Filter System features the exclusive 1-2-3 Safety Locking System to ensure safe and simple filter maintenance.

  1. Turn off pump.

    Never attempt to clean filter while pump is running. This is a pressurized vessel. It could cause severe injury or harm to your person.
    Plug skimmer and pool return lines or drain pool water level to below pool return line.
  2. Slowly open the air release knob on top of filter until the pressure gauge reads "0". Open drain cap at bottom of filter and allow water to flow.
  3. Press the yellow safety latch on the underside of the locking nut and turn the nut counterclockwise to remove the lid. Rinse the D.E. element with a garden hose. There is no need to remove the element from the filter.
  4. Reassemble lid and follow start-up procedures from original instructions.

2200 East Sturgis Road, Oxnard, CA 93030
Ph. (805) 981-0262
Fax (805) 981-9403
www.waterwayplastics.com
waterway@waterwayplastics.com

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Waterway CLEARWATER II - Water Filtration System Manual

Advertisement

Need help?

Need help?

Do you have a question about the CLEARWATER II and is the answer not in the manual?

Questions and answers

Table of Contents