▶ IEC 60364-7-701 must be observed when installing the appliance and or electrical accessories. ▶ The appliance must be installed in a Tronic 2000T – 6 720 885 113 (2021/08)
Page 4
“If the power cable is damaged, it must be replaced by the manufacturer, its customer service department or a similarly qualified person, so that risks are avoided.” Tronic 2000T – 6 720 885 113 (2021/08)
Use the appliance only in closed systems. Only use adequate solar liquid in the heat exchanger coil (if present). Using the appliance for any other purpose will be considered incorrect use. Bosch accepts no liability for any damage 6720801526-01.2V resulting from such use. Fig. 1...
HO5VV - F 3 x 1,0 mm or HO5VV - F 3 x 1,5 mm Protection class Type of protection IPX4 Water temperature Temperature ranges °C until 70 °C Table 3 Technical characteristics Tronic 2000T – 6 720 885 113 (2021/08)
[3] Heating element [4] Hot water outlet ½ ” male [5] Cold water inlet½ ” male [6] Magnesium anode [7] Thermal cut out [8] Thermostat Electrical wiring diagram Fig. 5 Electric circuit diagram Tronic 2000T – 6 720 885 113 (2021/08)
CAUTION: Damage to the heating elements! ▶ Firstly connect all the water connections 6 720 612 659-13.3TT and fill the appliance. Fig. 6 Protection areas ▶ Connect the appliance to the electric point, assuring connection to earth. Tronic 2000T – 6 720 885 113 (2021/08)
6720821785-02.1V Fig. 8 Installation under the sink [1] Cold water inlet (right hand side) [2] Hot water outlet (left hand side) Tronic 2000T – 6 720 885 113 (2021/08)
In the case of freezing: ▶ Switch off the appliance. ▶ Purge the appliance (chapter 6.3). -or- ▶ Do not disconnect the appliance from the electric current. Tronic 2000T – 6 720 885 113 (2021/08)
[1] Operating light [2] On / Off switch ▶ Switch off the water cutting valve and open a hot water tap. [3] Temperature selector ▶ Open the safety valve (Fig. 12). Tronic 2000T – 6 720 885 113 (2021/08)
▶ When carrying out maintenance work change the To dispose of old electrical or electronic disassembled joints and replace these with new ones. devices, you should use the return and collection systems put in place in the country concerned. Tronic 2000T – 6 720 885 113 (2021/08)
▶ Disconnect the connecting cables to the thermostat ▶ Loosen the fastening screws of the flange [1]. ▶ Remove the flange [2]. ▶ Verify the magnesium anode [3] and replace it if necessary. Tronic 2000T – 6 720 885 113 (2021/08)
▶ Turn off all the hot water taps, and position the thermostat higher power consumption and potential safety activation if on the normal working position. temperature limits are breached (manual resetting of thermostat necessary). Tronic 2000T – 6 720 885 113 (2021/08)
The abovementioned interventions are not covered by the appliance warranty. Required actions after any maintenance work has been carried out ▶ Refasten and check the fastness of all the water connections. ▶ Turn on the appliance. Tronic 2000T – 6 720 885 113 (2021/08)
▶ If necessary, install a pressure reducer (Fig. 9). ▶ Confirm the need for an expansion vessel (pre-load 0.5 bar below Pmax). Capacity of the water supply network. ▶ Check piping. Table 5 Tronic 2000T – 6 720 885 113 (2021/08)
Page 18
▶ Assess time necessary for reheating water, excessive consumption from water taps (Tab. 3). or leak in the hot water system. ▶ Replace the product with one that has sufficient capacity. Table 5 Tronic 2000T – 6 720 885 113 (2021/08)
Page 20
Egypt ROBERT BOSCH LTD. 52/54 Isaac John Street, Ikeja, GRA, Lagos Nigeria. Tel: +234 908 781 4939 ROBERT BOSCH EAST AFRICA LTD. 4th floor, Fedha Plaza P.o Box 856-00506 Westlands. Nairobi Kenya Tel: +254 74 2967640 / +254 70 0651436...