Advertisement
Troubleshooting Procedures
To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless
testing requires power.
Board Input Test
IN
While in Service Mode, pressing the
Spin & Drain key will begin the Board
Input Test. This test turns 'ON' a
specified output after a key press. Pressing the Spin &
Drain key again cancels the test. (Display shows "in").
While in Service Mode follow chart to check respective
function.
•
When the Rotary Cycle Selector knob is set to
"Super Wash" and the Rotary Cycle Selector knob
is pressed, the door position will be displayed: "0P" if
open, "CL" if closed.
•
When the Rotary Cycle Selector knob is set to
"Normal" and the Rotary Cycle Selector knob is
pressed, the Lock position will be displayed: "UL" if
unlocked, "L0" if locked.
•
When the Rotary Cycle Selector knob is set to
"Quick Wash" and the Rotary Cycle Selector knob
is pressed, the High water level will be displayed:
–
–
"
0" if below level, "
1" if above level. The High water
level is defined as the over flow water level.
•
When the Rotary Cycle Selector knob is set to
"Wrinkle Control" and the Rotary Cycle Selector
knob is pressed, the Medium water level will be
displayed: "—0" if below level, "—1" if above level.
The Medium water level is defined as the minimum
water level needed such that the heater can be
turned 'ON' (only MAH8700* and MAH9700* models
have heaters).
•
When the Extra Rinse key is pressed, the Low
water level will be displayed: "_0" if below level, "_1"
if above level. The Low water level is defined as the
reset water level.
•
When the Rotary Cycle Selector knob is set to
"Hand Wash" and the Rotary Cycle Selector knob
is pressed, the level of Tub unbalance will be
displayed: "UC" if balanced, "U0" if unbalanced. "U0"
will be displayed during the time when the machine
is correcting for the unbalance; e.g. slowing down to
redistribute the load or to get to a lower spin speed.
Once the situation has been corrected (i.e. the load
has begun tumbling or the lower speed has resulted
in an acceptable amount of balance); "UC" will once
again be displayed.
•
When the Delay Start key is pressed, the water
temperature will be displayed in Degrees F
(Fahrenheit).
•
When the Rotary Cycle Selector knob is set to
"Delicates" and the Rotary Cycle Selector knob is
pressed, the water temperature will be displayed in
degrees C (Celsius).
June 2006
©2006 Maytag Services
!
WARNING
•
When the Rotary Cycle Selector knob is set to
"Super Wash", the LED lights up. Revolve Rotary
Cycle Selector knob clockwise until all LED's are
'OFF', then press Rotary Cycle Selector knob to
display frequency reading. "25" means 25 Hz
(washer empty). Frequency value drops as water
rises.
While performing the Board Input Test in Service
Mode, follow this quick reference chart to check
respective functions.
Selection
Rotary Cycle
Selector set to
"Super Wash".
Press Rotary Cycle
Selector.
Rotary Cycle
Selector set to
"Normal". Press
Rotary Cycle
Selector.
Rotary Cycle
Selector set to
"Quick Wash".
Press Rotary Cycle
Selector.
Rotary Cycle
Selector set to
"Wrinkle Control".
Press Rotary Cycle
Selector.
Press the Extra
Rinse key.
Rotary Cycle
Selector set to
"Hand Wash".
Press Rotary Cycle
Selector.
Press Delay Start
key.
Rotary Cycle
Selector set to
"Delicates". Press
Rotary Cycle
Selector.
All cycle LEDs are
off, press Rotary
Cycle Selector
9
Function
Display
Door position
"0P" or "CL"
Lock state
"UL" or "L0"
–
"
0" if below
High water level
level. "
above level.
"
"
—0
Medium water
level. "—1" if
level
above level.
"_0" if below
Low water level
level. "_1" if
above level.
"UC" if
Balanced.
Tub balance
"U0" if
Unbalanced
Water
Degrees F
temperature
Water
Degrees C
temperature
"25" (empty).
Water Level
Frequency
Frequency(Hz)
drops as
water rises.
16027053
RPL 16026539
–
1" if
if below
Advertisement
