Advertisement
Troubleshooting Procedures
To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless
testing requires power.
Board Output Test
While in Service Mode, pressing the Spin
Speed key will begin the Board Output
Test. This test turns 'ON' a specified
output after a key press. Pressing the Spin Speed key
again cancels the test. Only one output can be 'ON' at
any time. All outputs will be turned 'OFF' after five (5)
minutes of inactivity.
•
When the Rotary Cycle Selector knob is set to
"Super Wash" and the Rotary Cycle Selector knob
is pressed, the main relay will be toggled (either
from 'ON' to 'OFF' or from 'OFF' to 'ON').
•
When the Rotary Cycle Selector knob is set to
"Normal" and the Rotary Cycle Selector knob is
pressed, the hot water valve will be turned 'ON'.
This output will remain 'ON' until the Rotary Cycle
Selector knob is pressed again to turn 'OFF' the
output. The control will not allow the machine to fill
past the High water level.
•
When the Rotary Cycle Selector knob is set to
"Wrinkle Control" and the Rotary Cycle Selector
knob is pressed, the cold water valve will be turned
'ON'. This output will remain 'ON' until the Rotary
Cycle Selector knob is pressed again to turn 'OFF'
the output. The control will not allow the machine to
fill past the High water level.
•
When the Rotary Cycle Selector knob is set to
"Delicates" and the Rotary Cycle Selector knob is
pressed, the bleach valve will be turned 'ON'. This
output will remain 'ON' until the Rotary Cycle
Selector knob is pressed again to turn 'OFF' the
output. The control will not allow the machine to fill
past the High water level. bleach valve
•
When the Rotary Cycle Selector knob is set to
"Hand Wash" and the Rotary Cycle Selector knob
is pressed, the bleach valve and the cold water
valve will be turned 'ON' to check the fabric softener
fill. This output will remain 'ON' until the Rotary
Cycle Selector knob is pressed again to turn 'OFF'
the output. The control will not allow the machine to
fill past the High water level.
•
When the Rotary Cycle Selector knob is set to
"Quick Wash" and the Rotary Cycle Selector is
pressed, the drain pump will be turned 'ON'. This
output will remain 'ON' until the Rotary Cycle
Selector knob is pressed again to turn 'OFF' the
output.
•
Pressing the Delay Start key will turn 'ON' the
motor and the Delay Start LED. This output and the
LED will remain 'ON' until the Delay Start key is
pressed again to turn 'OFF' the output. When
activated, the machine will tumble for 5 seconds in
the CW direction, pause for 2 seconds, tumble in
the CCW direction for 5 seconds, pause for 2
16027053
RPL 16026539
!
WARNING
seconds; repeating this pattern until Delay Start key
is pressed again to turn 'OFF' the tumbling.
Note: All tumble speeds are assumed to be 45 rpm.
•
Pressing the Chime key will unlock the door and
turn 'ON' all the LED's above the Chime key. This
output will attempt to unlock one time, if safe to do
so.
•
Pressing the Wash / Rinse Temp key will lock the
door and all the Wash / Rinse Temp LED's will turn
'ON'. Pressing the Chime key will unlock the door
and the all the Chime LED's will turn 'ON'.
While performing the Board Output Test in Service
Mode, follow this quick reference chart to check
respective function.
Selection
Rotary Cycle
Selector set to
"Super Wash". Press
Rotary Cycle
Selector.
Rotary Cycle
Selector set to
"Normal". Press
Rotary Cycle
Selector.
Rotary Cycle
Selector set to
"Wrinkle Control".
Press Rotary Cycle
Selector.
Rotary Cycle
Selector set to
"Delicates". Press
Rotary Cycle
Selector.
Rotary Cycle
Selector set to "Hand
Wash". Press Rotary
Cycle Selector.
Rotary Cycle
Selector set to
"Quick Wash". Press
Rotary Cycle
Selector.
Press Delay Start
Press Chime
Press Wash / Rinse
Temp
10
Component
Function
'ON' to 'OFF' or
Main Relay
'OFF' to 'ON'
st
1
press valve
Hot Water
nd
'ON'
. 2
Valve
valve 'OFF'.
st
1
press valve
Cold Water
nd
. 2
'ON'
Valve
valve 'OFF'.
st
1
press valve
Bleach
nd
'ON'
. 2
Valve
valve 'OFF'.
st
Bleach
1
press Fabric
Valve and
Softener Fill. 2
Cold Water
press valves
Valve
'OFF'
st
1
press Drain
Pump 'ON' . 2
Drain Pump
press Drain
Pump 'OFF'.
st
1
press Motor
nd
Motor
'ON'
. 2
Motor 'OFF'.
1 Attempt to
Door Lock
unlock
Door Lock
Lock Door
June 2006
©2006 Maytag Services
press
press
press
nd
nd
press
Advertisement
