La Crosse Technology 9245 - Wireless Temperature Station Manual

FEATURES

The Temperature Station

• Manual time set (hour and minute)
• 12-Hour Time Format
• Temperature Display in Farenheit (°F)
• Indoor and Outdoor Temperature with MIN/MAX Records
• Low Battery Indicator
• Wireless Transmission at 915 MHz
• 8 Second Signal Reception Interval
• Wall Mount or Table Stand

The Outdoor Temperature Transmitter

• Wireless 915 MHz Outdoor Temperature Transmitter
• Rain-resistant Casing
• Wall Mounting or Table Stand

Note: Mount in a sheltered place. Avoid direct rain and sunshine.

SETUP

Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel cadmium) batteries.

Note: This temperature station can only receive one transmitter only.

1. First, insert batteries into the transmitter, observing the correct polarity (see marking inside battery compartment).
2. Within 30 seconds of powering up the transmitter, insert batteries into the Temperature Station, observing the correct polarity (see marking inside battery compartment). Once the batteries are in place, all segments of the LCD will light up briefly. Following the indoor temperature, the time as 12:00 will be displayed. If they are not shown in the LCD after 60 seconds, remove the batteries and wait for at least 60 seconds before reinserting them. Once the indoor data is displayed you may proceed to the next step.
3. After the batteries are inserted, the Temperature Station will start receiving outdoor temp data from the transmitter. The outdoor temperature should then be displayed on the Temperature station. If this does not happen after 2 minutes, remove the batteries from both units and start again from step 1.
4. In order to ensure sufficient 915 MHz transmission, the outdoor transmitter should be placed a distance of no more than 200 feet (60 meters) from the Temperature Station and the transmitter (see notes on "Positioning").

FUNCTION KEYS

The Temperature Station has only two easy to use function keys:

SET key: Press and hold for about 3 seconds to enter the Manual setting mode.
+ key: Press to make adjustment in the setting mode. Press and hold to reset all MIN/MAX records

LCD SCREEN AND SETTINGS

MANUAL TIME SET

To manually set the time of the Temperature Station:

1. Press and hold the SET key for 3 seconds to enter the manual time setting mode.
2. The hour digit of the time display will be flashing.
3. Press the + key to adjust the hour (press and hold to allow fast advance). Press SET key to confirm and go to the minute setting.
4. The minute digit will be flashing. Press the + key to adjust the minute (press and hold to allow fast advance). Press SET key once more to return to normal display.

Note: If no buttons are pressed within approximately 8 seconds while in setting mode, the unit will return to normal operating mode.

VIEWING THE INDOOR TEMPERATURE AND MIN/MAX

The indoor temperature is displayed in the second section of the LCD along with the indoor MIN/MAX records:

Notes:

• The minimum temperature range: 14ºF to 99ºF (100ºF to 140ºF will show "99ºF").
• The maximum temperature range: 14ºF to 140ºF
• The MIN/MAX temperature resolution is 1ºF
• The resolution of the indoor temperature is 0.5ºF

VIEWING THE OUTDOOR TEMPERATURE AND THE MIN/ MAX

The outdoor temperature is displayed in the last section of the LCD along with the outdoor MIN/MAX records:

Notes:

• The MIN/MAX temperature resolution is 1ºF
• The resolution of the outdoor temperature is 0.2ºF

TO RESET THE MIN/MAX DATA

The MIN/MAX temperature can be reset manually by pressing and holding the + key for about 3 seconds. This will reset all indoor and outdoor MIN/MAX temperature to current indoor and outdoor temperatures.

POSITIONING THE REMOTE TEMPERATURE TRANSMITTER

The remote temperature transmitter can be placed onto any flat surface or wall mounted using the bracket which doubles as a stand or wall mount base.

To wall mount:
Secure the bracket onto a desired wall using the screws and plastic anchors.

Clip the remote temperature transmitter onto the bracket.

Note: The mounting surface can affect the transmission range. If, for instance, the unit is attached to a piece of metal, it may then either reduce or increase the transmitting range. For this reason, we recommend not to place the unit on any metal surfaces or in any position where a large metal or highly polished surface is in the immediate vicinity (garage doors, double glazing, etc.). Before securing in place, please ensure that the Temperature Station can receive the 915MHz signal from the temperature transmitter at the positions that you wish to place them.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download La Crosse Technology 9245 - Wireless Temperature Station Manual