Ricoh Aficio 3228C Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Ricoh Manuals
  4. Printer Accessories
  5. Aficio 3228C
  6. Installation instructions manual
Ricoh Aficio 3228C Installation Instructions Manual

Ricoh Aficio 3228C Installation Instructions Manual

Scanner accessibility option
Hide thumbs Also See for Aficio 3228C:
1
2
3
4
5
6
7
8

Advertisement

Table of Contents

See also: Network Manual , Manual
SCANNER ACCESSIBILITY OPTION
(Machine Code: G570)

INSTALLATION PROCEDURE

For Machine code:
B178/B180/B202 Copiers
NOTE: THE SCANNER ACCESSIBILITY OPTION MUST BE INSTALLED BY
A CUSTOMER SERVICE REPRESENTATIVE WHO HAS
COMPLETED THE TRAINING COURSES ON THE BASE COPIER
AND THE SCANNER ACCESSIBILITY OPTION.
G5708560
G5708560

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Aficio 3228C and is the answer not in the manual?

Questions and answers

Related Manuals for Ricoh Aficio 3228C

Summary of Contents for Ricoh Aficio 3228C

  • Page 1: Installation Procedure

    SCANNER ACCESSIBILITY OPTION (Machine Code: G570) INSTALLATION PROCEDURE For Machine code: B178/B180/B202 Copiers NOTE: THE SCANNER ACCESSIBILITY OPTION MUST BE INSTALLED BY A CUSTOMER SERVICE REPRESENTATIVE WHO HAS COMPLETED THE TRAINING COURSES ON THE BASE COPIER AND THE SCANNER ACCESSIBILITY OPTION. G5708560 G5708560...

  • Page 2: Installation Requirements

    INSTALLATION REQUIREMENTS Machine Level Front to back: Within 5 mm (0.2")/ 5° Right to left: Within 5 mm (0.2")/ 5° Location Requirement Put the scanner on the right side of the mainframe as shown. NOTE: 1) Make sure that the scanner is placed 660~724 mm above the floor. 2) Make sure that the scanner cable does not touch the floor.
  • Page 3 ACCESSARY CHECK Check the accessories and their quantities against the following list. Description 1. Exposure Glass Cleaner Holder ... 1 2. Exposure Glass Cleaner ... 1 3. M3 x 6 screw... 12 4. M3 x 8 screw... 1 5. Ground screw ... 1 6.
  • Page 4 INSTALLATION PROCEDURE NOTE: This installation procedure uses the following symbols. !: Screws ": Connectors #: Clamps CAUTION Unplug the copier power cord before you do the following procedure. 1. Remove the all tapes. 2. Remove rear cover [A] (! x 5). 3.
  • Page 5 5. Remove the DF connector cable [A] (! x 2, " x1). NOTE: Keep these screws. You will use these screws later. 6. Remove the connector bracket [B]. 7. Disconnect the connector [C] of the IPU harness and release the clamp [D]. 8.
  • Page 6 G570I305.WMF 14. Disconnect the PSU cable connector [A]. 15. Detach the SIO board with bracket [B] (! x 4). Then slide it to the right slightly. 16. Attach the bracket [C] (! x 5). 17. Attach the SIO board with the bracket again (! x 4). G570I306.WMF 18.
  • Page 7 20. Put the I/F cable [A] through the opening on the frame. Then attach the core [B] to the I/F cable. 21. Connect the I/F cable connector [C]. Then attach the cable holder [D] (! x 1) and the ground [E] (! x 1) to the frame. 22.
  • Page 8 24. Connect the PSU cable connector [A] and attach the ground [B] (ground screw x 1). 25. Attach the scanner bracket [C] to the supports (! x 3) and the ground [D] (! x 26. Install the duct (! x 2, " x 1) and ground cable (! x 2). 27.

This manual is also suitable for:

B178B180B202G570

Table of Contents