Subscribe to Our Youtube Channel
Related Manuals for GATEXPERT GK Series
Summary of Contents for GATEXPERT GK Series
- Page 1 INDUSTRIAL DOOR OPERATOR USER MANUAL GK SERIES Website: www.gatexpertstore.com E-mail: sales@gatexpertstore.com...
- Page 2 All personal information you provided will be only used for warranty service and kept strictly confidential. Refer to this list when contacting GATEXPERT for technical service or assistance with your automatic gate opener. Order Number Product Model...
- Page 3 Instructions for GK SERIES Dear users, Thank you for choosing this product. Please read the manual carefully before assembling and using it. Please do not leave out the manual if you send this product to a third party. Safety Instruction 1.
-
Page 4: Table Of Contents
Instructions for GK SERIES CONTENTS 1. Technical Parameter Table ……….……………………………...…………….……1 2. Dimension and Component of Industrial Door Operator …....……3 3. Installation Guide of Industrial Door Operator ………..…………...……4 4. Industrial Door Operator Wiring ……………………..………………..…..…... 7 5. GK220 Control Panel Wiring (AC220V) ………….…….………….……….. -
Page 5: Technical Parameter Table
Instructions for GK SERIES Industrial Door Operator Technical Parameter Model (Single Phase AC220V±10%) GK40 GK60 GK100 Rated Power 300W 400W 550W Torque 40N.m 60N.m 100N.m No-load Continuous Running Time 15min 8min Model (Three Phase AC380V±10%) GK60S GK100S GK150S Rated Power... - Page 6 Instructions for GK SERIES Loop Detector (Sense Coil) Available (Optional) Available (Optional) www.gatexpertstore.com...
-
Page 7: Dimension And Component Of Industrial Door Operator
Instructions for GK SERIES Dimension and Component of Industrial Door Operator ①Gearbox ②Mechanical limit cam ③Terminals ④Plastic cover ⑤ Motor ⑥Hand-pulled chain ⑦Pull cord switch www.gatexpertstore.com... -
Page 8: Installation Guide Of Industrial Door Operator
Instructions for GK SERIES Installation Guide of Industrial Door Operator The industrial door operator is mainly used in the industrial sectional door equipped with balance spring, but also can applied in lifting industrial door. The installation of door machine has two forms, shaft drive and chain drive. The factory standard configuration is shaft drive. - Page 9 Instructions for GK SERIES 2) Determine the installation position Consider the boundary dimension and installation direction of the door machine, determine the position of the mounting bracket, mark the insert cavity position, drill the screw hole and fix the mounting bracket. (The mounting bracket can be fixed inside and outside the door machine, recommended to be installed inside, for the convenience of disassembly of door machine).
- Page 10 Instructions for GK SERIES 5) Find the direction of key slot First pull the red handle A to the bottom to make the hand-pulled chain mechanism enga ge with the main engine (Manual control mode). Rotate the output shaft of industrial door operator by pulling the hand-pulled chain up and down until the key slot of the output shaft is fully aligned with the key slot of the door shaft.
-
Page 11: Industrial Door Operator Wiring
Instructions for GK SERIES Industrial Door Operator Wiring Pull the cable through the waterproof connector on the main engine, connect it with the terminal inside the industrial door operator according to the instruction of cable marker. CL CO OP NC CO NO... -
Page 12: Gk220 Control Panel Wiring (Ac220V)
Instructions for GK SERIES GK220 Control Panel Wiring (AC220V) Wiring of power, motor and limit switch of GK40, GK60, and GK100 single phase control box as shown below ① Single Phase Power Wire L, N ② Motor Wire (U BLUE, V BROWN, W BLACK) ③ Capacitor Wire (C BLUE, C BROWN) ④... -
Page 13: Gk380 Control Panel Wiring (Ac380V)
Instructions for GK SERIES GK380 Control Panel Wiring (AC 380V) Wiring of power, motor and limit of GK60S, GK100S and GK150S three phase control box as shown below ① Three Phase Power Wire L1, L2, L3 ② Power Neutral Wire N ③ Motor Wire (U RED, V WHITE, W BLACK) ④... -
Page 14: Usage Of Hand-Pulled Chain
Instructions for GK SERIES Usage of hand-pulled chain When you need to manually open or close the industrial door, then hand-pulled chain would be required. Before pulling the chain, please fully pull the red handle A in the hand-pulled chain mechanism to make it engage with the main machine. -
Page 15: Setting And Adjustment Of Limit
Instructions for GK SERIES Setting and Adjustment of Limit Limit Switch Structure: ① Passive Signal Cam (GREEN) ② ③ Open Limit Cam (GREEN) ④ ⑤ Close Limit Cam (RED) ⑥ Passive Signal Micro switch ⑦ ⑧ Open Signal Micro switch (N.C.) ⑨... -
Page 16: Fitting Wiring
Instructions for GK SERIES with the original cam rotation direction, the close limit switch moves up and the close position will be higher. Otherwise close position will be lower; under normal circumstances, if the hex wrench is rotated 90 °, the close position will differ by around 25mm. - Page 17 Instructions for GK SERIES 3. The door in door switch is wired with "DET" and "CO" (State as delivered is N.C.). When connect the door in door switch, please remove the short circuit wire jumper between "DET" and "CO". 4. External three button switch should be connected with OPN, CLS, STP, COM (State as delivered is N.O.).
-
Page 18: Setting And Debugging Of Control Box
Instructions for GK SERIES Setting and Debugging of Control Box After confirming the wiring, turn on the power for the debugging of next step (the following debugging steps can be applied to both single phase and three phases control box): a. - Page 19 Instructions for GK SERIES b. Delete remote control: Delete remote control that have been learned; press the learning button AN1 and indicator light will be on; loosen the button until LED2 is off. This indicates that all remote controls that learned previously have been deleted.
-
Page 20: Common Faults And Countermeasures
Instructions for GK SERIES Common Faults and Countermeasures Trouble Possible Cause Countermeasures 1.The power supply is not connected or the Tighten the screw of the wire connector is wiring and re-power on. loose. 2.The emergency stop Reinsert the emergency The STOP indicator... - Page 21 Instructions for GK SERIES Exchange the two wires 1.Motor wires U, V and V and W on the control W are wired The opening and incorrectly. closing directions are box. opposite to the control Exchange the two wires box buttons.
-
Page 22: Packing List
Instructions for GK SERIES PACKING LIST Main Engine Packing Box Name Amount Note Main engine Mounting bracket Contain M6×10 Fixing sleeve fastening screw Special wrench Special flat key 6×70 Hexagon head flange bolts M10×20 User manual Control Unit Packing Box GK220, GK380...
Need help?
Do you have a question about the GK Series and is the answer not in the manual?
Questions and answers