Subscribe to Our Youtube Channel
Related Manuals for GATEXPERT GT1000DC
Summary of Contents for GATEXPERT GT1000DC
- Page 1 Sliding Gate Opener User Manual GT1000DC Website: www.gatexpertstore.com E-mail: sales@gatexpertstore.com...
- Page 2 Instructions for GT1000DC WARNING Instructions must be read before installation. Please follow these instructions carefully, incorrect installation could affect gate operation. When mounting and positioning this product please ensure the power cable is unplugged. The motor cover will need to be removed to mount the motor to the mounting plate or directly to the concrete footing.
- Page 3 All personal information you provided will be only used for warranty service and kept strictly confidential. Refer to this list when contacting GATEXPERT for technical service or assistance with your automatic gate opener. Order Number Product Model...
-
Page 4: Table Of Contents
Instructions for GT1000DC CONTENTS Default Setting Instruction......................1 Safety Instruction..........................2 Parts List............................3 Technical Parameters........................5 Installation............................5 Before You Start..........................5 Tools Required / Example Sliding Gate………................5 Step 1 - Gate Preparation......................6 Step 2 - Checking Manual Release.....................6 Step 3 - Removing / Installing Motor Cover.................7 Step 4 –... -
Page 5: Default Setting Instruction
Instructions for GT1000DC Default Setting Instruction The gate opener will open the gate to the right-hand side as its default setting. By default, the opener mounts on the right-hand side. (Figure 1) Gate in closed position Gate in open position... -
Page 6: Safety Instruction
Instructions for GT1000DC Safety Instruction Warning: Incorrect or improper use of this product can cause damage to persons, animals or properties. · Please ensure that the input voltage used matches with the supply voltage of gate opener. · All modifications to wiring or electrics, and any adjustment or maintenance to input voltage must be done by a qualified electrician. -
Page 7: Parts List
Instructions for GT1000DC Parts List Parts List (standard configuration) Picture Name Quantity Motor Manual Release Keys Remote Controls Spring Limit Switch Accessories Box/ Magnetic Limit Switch Accessories Box Spring Limit Switch Stop 1 set 4-1-1 Spring Limit Switch Stop Mounting Screw M6X10... - Page 8 Instructions for GT1000DC Picture Name Quantity Foundation Bolts Nuts M10 Flat Washers φ10 Spring Washers φ10 Note: Extra flat washers and spring washers are spare parts. Parts List (optional) Picture Name Quantity Galvanized Gear Rack 1m/pc Nylon Gear Rack 1m/pc...
-
Page 9: Technical Parameters
Installation Before You Start · GT1000DC Sliding Gate Automation Kit is suitable for powering the opening and closing motion of gates up to 800kg in weight, up to a length of 12m. · Gate motion is achieved by the rotating output gear of the gate opener driving the gear rack (sold separately) fitted to the moving gate. -
Page 10: Step 1 - Gate Preparation
Instructions for GT1000DC Example Sliding Gate Gate Track and Track Wheels Gate End Catch Gate Guide Rollers Gate Stop Figure 4 Please ensure that the gate opener power cable is not plugged in at any stage before Step 8. Step 1 - Gate Preparation ·... -
Page 11: Step 3 - Removing / Installing Motor Cover
Instructions for GT1000DC Turn 90° To make the motor into manual mode, insert the key In manual mode, the gear and open the manual release bar till it rotates by 90°. can turn freely and the gate can be operated by hand. -
Page 12: Step 4 - Motor Pad Footing
Instructions for GT1000DC Step 4 - Motor Pad Footing · The motor pad concrete footing requires an area of no less than 450mm long x300mm wide and a minimum depth of 200mm (Standard requirement). · Ensure surface is level and parallel to the driveway. - Page 13 Instructions for GT1000DC Spring Washer Flat Washer Flat Washer The bolts and flat washer between mounting plate and motor base are used for adjusting the height of the motor. Figure 10 With Mounting Plate · Pre embed the anchor bolts as per Φ10 holes in Figure 8 before concreting, after hardening, place the mounting plate, fit and tighten anchor bolts.(as per figure 11).
-
Page 14: Step 6 - Gear Rack & Motor Alignment
Instructions for GT1000DC Fitting Motor · Fit motor and mounting plate(if with) on the concrete footing. · Ensure the motor output gear and gear rack are correctly aligned. Gear and gear rack should be centered as much as possible. ·... -
Page 15: Step 7 - Limit Switch Stops
Instructions for GT1000DC Output Gear Spring/Magnetic Limit Switch Figure 15 Step 7 - Limit Switch Stops Included in your gate opener kit are two limit switch stops which must be fitted to the gear racks on your gate to ensure safe operation. - Page 16 Instructions for GT1000DC · Fit limit switch stop onto the top of gear rack at the point where it meets the Spring/Magnetic limit switch on the motor. · Tighten locking screws of limit switch stop. Spring limit switch Magnetic limit switch Open Position ·...
- Page 17 Instructions for GT1000DC Magnetic limit switch Test the spring/magnetic limit switch stops by moving the gate manually until you hear a click, making sure contact is made with the spring/magnetic limit switch on the motor. To Reset: Turning the power off will reset the limit switch stop memory. Power on the gate opener again, pressing remote control or external push button switch to open and then close the gate once, then new limit switch stop setting is completed.
-
Page 18: Step 8 - Powering On
Instructions for GT1000DC Motor cover Spring limit switch Limit switch stop Output gear Gear rack Mounting plate Motor cover Magnetic limit switch Output gear Gear rack Mounting plate Open Position Step 8 - Powering on · Ensure that the outer cover has been fitted and fastened back onto the motor base. -
Page 19: Step 9 - Testing Travel And Limit Stops
Instructions for GT1000DC · Plug the power cord into an approved RCD protected weatherproof outlet. · Remote controls included in this kit are factory paired ready for use. Figure 16 Step 9 - Testing Travel and Limit Stops Testing the Closed Position ·... - Page 20 Instructions for GT1000DC Now the basic open and closed positions are set, for further setting functions and adjusting parameters, please refer to pages 17-27 in this manual. www.gatexpertstore.com...
-
Page 21: Programming And Wiring
Instructions for GT1000DC Programming and Wiring Any works to the 110V/220V AC must only be performed by a licensed electrician. Ensure power is off before any modifications are made. Dip Switches Potentiometers Learn Button J8 Terminal J1 Terminal J4 Terminal... -
Page 22: Dip Switch Adjustment
Instructions for GT1000DC DIP Switch Adjustment All changes to these settings must be completed by a licensed electrician Figure 18 Number Function Description Automatic close time setting: the gate is operated to open by remote control operation and will close automatically after a few seconds delay. -
Page 23: Potentiometer Adjustment
Instructions for GT1000DC ON–enable OFF–disable Auto-reverse Function Default position is ON, this should align with the opener status and is not recommended to be modified by the users. ON–enable Photocell Delay OFF–disable Detection Please enable this function if your motor is... -
Page 24: Terminal Instructions
Instructions for GT1000DC Terminal Instructions All changes to these settings below must be completed by licensed electrician. J8 Terminal: (as per Figure 17): Terminal ALM+: Alarm Lamp +24VDC Terminal ALM-: Alarm Lamp -24VDC J1 Terminal: Terminal 5: Common Terminal for Photocell Terminal 6: Photocell Input (N.C.). -
Page 25: Wiring To The Terminal
Instructions for GT1000DC Wiring to the Terminal Insert the wire into the Using a screwdriver to Tighten with a screwdriver number on the terminal that loosen the screw on the to secure the wire in place. you are looking to connect to. -
Page 26: Connecting Infrared Photocells
Instructions for GT1000DC Connecting Infrared Photocells The below steps must be completed by licensed electrician. Highly recommend the use of infrared photocells as an additional safety feature. While closing, if the ray of the Infrared Photocell is blocked, the gate will stop and reverse immediately, to protect user and property security. -
Page 27: Remote Control Operation
Instructions for GT1000DC Remote Control Operation Three button mode remote control: OPEN/CLOSE/STOP of motor are controlled by three buttons separately on the remote control. Single button mode remote control: OPEN/CLOSE/STOP of motor are controlled by one button circularly on the remote control. -
Page 28: Connecting Storage Battery
Instructions for GT1000DC Connecting Storage Battery Charger Charger C3 C3 J2 J2 D6 D6 F1 F1 BAT+ BAT+ DKC500DC.PCB DKC500DC.PCB R8 R8 R9 R9 2015.01.05 2015.01.05 Control Control board board － ＋ Storage Storage battery battery － ＋ Figure 23... -
Page 29: Wiring To The Transformer
Instructions for GT1000DC Wiring to the Transformer Transformer Transformer input input 220VAC 220VAC Transformer Transformer output output 24VAC 24VAC C3 C3 J2 J2 D6 D6 F1 F1 BAT+ BAT+ DKC500DC.PCB DKC500DC.PCB R8 R8 R9 R9 2015.01.05 2015.01.05 Figure 25 Maintenance The gate should be checked every month to make sure it operates normally. -
Page 30: Troubleshooting
Instructions for GT1000DC Troubleshooting Any troubleshooting work below done to the motor must be completed by a licensed electrician and only whilst the power is off and the motor is unplugged! Problem Possible Reason Solution 1. The power supply is Connect the power supply. -
Page 31: Drawing And Measurements
Instructions for GT1000DC Drawing and Measurements Figure 26...
Need help?
Do you have a question about the GT1000DC and is the answer not in the manual?
Questions and answers