Subscribe to Our Youtube Channel
Related Manuals for GATEXPERT GT1000DCL
Summary of Contents for GATEXPERT GT1000DCL
- Page 1 Sliding Gate Opener User Manual GT1000DCL Website: www.gatexpertstore.com E-mail: sales@gatexpertstore.com...
- Page 2 Instructions for GT1000DC WARNING Instructions must be read before installation. Please follow these instructions carefully, incorrect installation could affect gate operation. When mounting and positioning this product please ensure the power cable is unplugged. The motor cover will need to be removed to mount the motor to the mounting plate or directly to the concrete footing.
- Page 3 All personal information you provided will be only used for warranty service and kept strictly confidential. Refer to this list when contacting GATEXPERT for technical service or assistance with your automatic gate opener. Order Number Product Model...
-
Page 4: Table Of Contents
Instructions for GT1000DCL CONTENTS Default Setting Instruction......................1 Safety Instruction..........................2 Parts List............................3 Technical Parameters........................5 Installation............................5 Before You Start..........................5 Tools Required / Example Sliding Gate………................6 Step 1 - Gate Preparation......................6 Step 2 - Checking Manual Release.....................7 Step 3 - Removing / Installing Motor Cover.................7 Step 4 –... -
Page 5: Default Setting Instruction
Instructions for GT1000DCL Default Setting Instruction The gate opener will open the gate to the right-hand side as its default setting. By default, the opener mounts on the right-hand side. (Figure 1) Gate in closed position Gate in open position... -
Page 6: Safety Instruction
Instructions for GT1000DCL Safety Instruction Warning: Incorrect or improper use of this product can cause damage to persons, animals or properties. · Please ensure that the input voltage used matches with the supply voltage of gate opener. · All modifications to wiring or electrics, and any adjustment or maintenance to input voltage must be done by a qualified electrician. -
Page 7: Parts List
Instructions for GT1000DCL Parts List Parts List (standard configuration) Picture Name Quantity Motor Manual Release Keys Remote Controls Mounting Accessories Box Sprocket Cover Chain(Including 2 Chain Links) Tie Rod Square Screw Round Screw Door Connecting Plate Horizontal Mounting Plate Vertical Mounting Plate Foundation Bolts M10 www.gatexpertstore.com... - Page 8 Instructions for GT1000DCL Picture Name Quantity Magnetic Limit Switch Stop Magnets 4-10 Hexagon Head Bolt M6X65 Nut M10 Flat Washer φ10 Spring Washers φ10 4-11 Inner Hexagon Head Bolt M6X20 4-12 Hexagon Head Bolt M10X50 Nut M6 4-13 Nut M8 Nut M10 Flat Washer φ6...
-
Page 9: Technical Parameters
Before You Start · GT1000DCL Sliding Gate Automation Kit is suitable for powering the opening and closing motion of gates up to 800kg in weight, up to a length of 12m. (Standard kit contains a 6m chain, if the gate length is over 5.5m, please consider to extend the length of the chain.) -
Page 10: Tools Required / Example Sliding Gate
Instructions for GT1000DCL Tools Required · Tape measure · Level · 12mm concrete drill and hammer (when uses expansion screws) · Phillips head screwdriver · Straight screwdriver Example Sliding Gate Gate Track and Track Wheels Gate End Catch Gate Guide Rollers... -
Page 11: Step 2 - Checking Manual Release
Instructions for GT1000DCL Step 2 - Checking Manual Release · Insert the key and open the manual release bar to enable the motor get into manual mode and check that the motor output sprocket rotates freely by hand (Figure 6). -
Page 12: Step 4 - Motor Pad Footing
Instructions for GT1000DCL Please Note: the rubber grommet must be fitted back onto the motor cover once the cover has been re-fitted/replaced onto the base of the motor. Step 4 - Motor Pad Footing · The motor pad concrete footing requires an area of no less than 500mm long x 400mm wide and a minimum depth of 250mm (Standard requirement). - Page 13 Instructions for GT1000DCL Spring Washer Flat Washer Flat Washer Figure 11 Fitting Motor · Fit motor and mounting base on the concrete footing. · Ensure the motor output sprocket and chain are correctly aligned. Sprocket and chain should be centered as much as possible.
-
Page 14: Step 6 - Sprocket And Chain & Motor Alignment
Instructions for GT1000DCL Figure 12 Step 6 - Sprocket and Chain & Motor Alignment · Ensure output sprocket and chain are correctly aligned. Under no circumstances should the gate opener output sprocket carry any weight of the gate. It is the task of the gate castors or wheels to carry the weight of the gate. -
Page 15: Step 7 - Limit Switch Stops
Instructions for GT1000DCL Sprocket Chain Figure 14 Step 7 - Limit Switch Stops Included in your gate opener kit are two limit switch stops which must be fitted on your gate to ensure safe operation. The limit switch stops are designed to set the desired opening and closing position of your gate. - Page 16 Instructions for GT1000DCL Magnetic limit switch switch Open Position · Position gate 150-200mm back from the gate stop open position. This will help in making sure you do not slam the gate into the end stop/catch when setting the open position under power.
-
Page 17: Step 8 - Powering On
Instructions for GT1000DCL Open Position Limit Switch Stop Closed Position Limit Switch Stop Motor Magnet Gate To Reset: Turning the power off will reset the limit switch stop memory. Power on the gate opener again, pressing remote control or external push button switch to open and then close the gate once, then new limit switch stop setting is completed. -
Page 18: Step 9 - Testing Travel And Limit Stops
Instructions for GT1000DCL Step 9 - Testing Travel and Limit Stops Testing the Closed Position · Ensure gate opener is installed as per step 5, 6 and 7 and the sliding gate is in the middle position. · Press remote (remotes included in kit are factory paired to the motor). The sliding gate will begin to close. -
Page 19: Programming And Wiring
Instructions for GT1000DCL Programming and Wiring Any works to the 110V/220V AC must only be performed by a licensed electrician. Ensure power is off before any modifications are made. Dip Switches Potentiometers Learn Button J8 Terminal J1 Terminal J4 Terminal... -
Page 20: Dip Switch Adjustment
Instructions for GT1000DCL DIP Switch Adjustment All changes to these settings must be completed by a licensed electrician Figure 17 Number Function Description Automatic close time setting: the gate is operated to open by remote control operation and will close automatically after a few seconds delay. -
Page 21: Potentiometer Adjustment
Instructions for GT1000DCL ON–enable OFF–disable Auto-reverse Function Default position is ON, this should align with the opener status and is not recommended to be modified by the users. ON–enable Photocell Delay OFF–disable Detection Please enable this function if your motor is... -
Page 22: Terminal Instructions
Instructions for GT1000DCL Terminal Instructions All changes to these settings below must be completed by licensed electrician. J8 Terminal: (as per Figure 17): Terminal ALM+: Alarm Lamp +24VDC Terminal ALM-: Alarm Lamp -24VDC J1 Terminal: Terminal 5: Common Terminal for Photocell Terminal 6: Photocell Input (N.C.). -
Page 23: Wiring To The Terminal
Instructions for GT1000DCL Wiring to the Terminal Insert the wire into the Using a screwdriver to Tighten with a screwdriver number on the terminal that loosen the screw on the to secure the wire in place. you are looking to connect to. -
Page 24: Connecting Infrared Photocells
Instructions for GT1000DCL Connecting Infrared Photocells The below steps must be completed by licensed electrician. Highly recommend the use of infrared photocells as an additional safety feature. While closing, if the ray of the Infrared Photocell is blocked, the gate will stop and reverse immediately, to protect user and property security. -
Page 25: Remote Control Operation
Instructions for GT1000DCL Remote Control Operation Three button mode remote control: OPEN/CLOSE/STOP of motor are controlled by three buttons separately on the remote control. Single button mode remote control: OPEN/CLOSE/STOP of motor are controlled by one button circularly on the remote control. -
Page 26: Connecting Storage Battery
Instructions for GT1000DCL Connecting Storage Battery Charger Charger C3 C3 J2 J2 D6 D6 F1 F1 BAT+ BAT+ DKC500DC.PCB DKC500DC.PCB R8 R8 R9 R9 2015.01.05 2015.01.05 Control Control board board － ＋ Storage Storage battery battery － ＋ Figure 22... -
Page 27: Wiring To The Transformer
Instructions for GT1000DCL Wiring to the Transformer Transformer Transformer input input 220VAC 220VAC Transformer Transformer output output 24VAC 24VAC C3 C3 J2 J2 D6 D6 F1 F1 BAT+ BAT+ DKC500DC.PCB DKC500DC.PCB R8 R8 R9 R9 2015.01.05 2015.01.05 Figure 24 Maintenance The gate should be checked every month to make sure it operates normally. -
Page 28: Troubleshooting
Instructions for GT1000DCL Troubleshooting Any troubleshooting work below done to the motor must be completed by a licensed electrician and only whilst the power is off and the motor is unplugged! Problem Possible Reason Solution 1. The power supply is Connect the power supply. -
Page 29: Drawing And Measurements
Instructions for GT1000DCL Drawing and Measurements Figure 25 www.gatexpertstore.com...
Need help?
Do you have a question about the GT1000DCL and is the answer not in the manual?
Questions and answers