Advertisement
Mounting Locations of Power Supply
Power supply
mounting locations (6)
6.
Connect the included 5 ft 10 in. (1.78 m) power cord to the power
jack on top of the power supply, and then connect the other end
to a power source. Do not apply power until all modules have
been installed and all connections have been made to the FlipTop
assembly.
Install the Modules
NOTE:
Installation procedures for most modules are available in
separate product documentation. For more information, refer to the
specific product manual located at www.crestron.com/manuals.
The following sections provide best practices and installation
procedures for pass-through cable modules and blank plate modules.
Position the Modules
NOTE:
The FlipTop assembly includes six FT2A-PLT-PT pass-through
cable modules and two FT2A-PLT-BLANK blank plate modules. No
other modules are included.
Follow the best practices below when performing module installation.
•
Perform module installation in the following order:
1.
AC Power Outlet Modules (FT2A-PWR-US)
2.
Retractor modules (FT2A-CBLR-1T and FT2A-CBLR-GR)
3.
All other modules (FT2A-CP, FT2A-CHGR-USBA/C,
FT2A-PLT-PT, and FT2A-PLT-BLANK)
•
Place the FT2A-CBLR-GR modules only at the ends of a module
row.
•
Dress all cables after installing each module.
Compliance and Legal
Original Instructions: The U.S. English version of this document is the original instructions. All
other languages are a translation of the original instructions.
As of the date of manufacture, the product has been tested and found to comply with
specifications for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following
conditions: (1) This device may not cause harmful interference and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Install the Pass-Through Cable Module
Each pass-through cable module is packaged with one nylon grommet
and one cable plate. One empty module slot is required for installation.
To assemble and install the pass-through cable modules into the FlipTop
assembly:
1.
Separate the grommet.
2.
Insert the cable into the grommet with the connector facing up
toward the end user.
NOTE:
The grommet is optional. It fits 10mm or smaller cables
(non-4K cables such as USB, CAT6, VGA, and audio). Omit the
grommet if installing larger cables (such as Crestron 4K video
cables) into the module.
3.
Press the grommet back together to secure the cable inside.
4.
Push the grommet and cable into the hole in the cable plate.
5.
Insert the cable plate into one of the three slots in the
pass-through module. The top of the cable connector should sit
flush with the top of the module.
NOTE:
If the cable connector extends past the top of the
pass-through module, the FlipTop assembly lid cannot close.
Location of Cable Plates within the Pass-Through Cable Module
Pass-through
The cable plate
with the nylon
module (with side
grommet may be
plate removed)
installed in one of
these three slots.
6.
Attach the side plate to the module by snapping the plastic clips
on the plate into the two slots on the module.
NOTE:
Ensure that the cable moves freely in the module prior to
attaching the side plate, as the plate is difficult to remove once
it is attached. If the side plate must be removed, use a small, flat
object (such as a flat-head screwdriver) to carefully pry the plastic
clips on the side plate off of the module near the two slots.
Location of Plastic Clips on Side Panel
Snap to attach
(or pry to remove)
the plastic clips
from the slots on
a pass-through
module.
7.
Feed the other end of the cable through an empty module slot in
the FlipTop assembly.
8.
Slide the pass-through cable module into the empty module slot
in the FlipTop assembly. Use the guide ribs on the front and rear of
each module to help position the module in the assembly.
CAUTION:
Changes or modifications not expressly approved by the manufacturer responsible
for compliance could void the user's authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Install the Blank Plate Module
Two blank plate modules are included to fill empty slots in module rows.
Each module requires one empty module slot for installation.
Blank Plate
Blank plate module
To install a blank plate module into the FlipTop assembly, slide the
module down into the appropriate module slot. Use the guide ribs on
the front and rear of the module to help position it in the assembly.
Install the Locking Bars
1.
Place the locking bars into position so that the screws attached to
the locking bars engage the screw holes in the FlipTop assembly.
2.
Using a manual torque screwdriver set to its lowest possible
setting, hand tighten the locking bar screws until the locking bars
are secured to the FlipTop assembly.
CAUTION:
Do not overtighten the locking bar screws.
Position of Locking Bars
Locking
bars (3)
FlipTop
assembly
Install the Bezel
Place the bezel onto the FlipTop assembly so that the retractable lids fit
inside the bezel openings. The bezel is held in place using magnets.
•
Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3 (B)/NMB-3(B)
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, please visit
www.crestron.com/opensource.
Crestron, the Crestron logo, Cresnet, and FlipTop are either trademarks or registered
trademarks of Crestron Electronics, Inc. in the United States and/or other countries. HDBaseT
is either a trademark or registered trademark of the HDBaseT Alliance in the United States
and/or other countries. HDMI and the HDMI logo are either trademarks or registered
Position of Bezel
Bezel
opening
for
retractable
lid
Lid
retraction
button
Retractable
lid
Operate the FlipTop Assembly
To operate the FlipTop assembly:
1.
Tap the lid retraction button to retract the one-touch lid, which
disappears into the assembly.
2.
Pull out a cable and lay it on the tabletop.
3.
Lift the cable vertically above the FlipTop assembly to retract the
cable gently back into the assembly.
4.
Close the lid by lifting it vertically and returning it over the FlipTop
assembly.
Additional Information
Scan or click the QR code for detailed product information on the
Crestron website.
FT2-500-ELEC
trademarks of HDMI Licensing LLC in the United States and/or other countries. The UR logo
is either a trademark or registered trademark of Underwriters Laboratories, Inc. in the United
States and/or other countries. USB Type-C is either a trademark or registered trademark of
the USB Implementers Forum in the United States and/or other countries. Other trademarks,
registered trademarks, and trade names may be used in this document to refer to either the
entities claiming the marks and names or their products. Crestron disclaims any proprietary
interest in the marks and names of others. Crestron is not responsible for errors in typography
or photography.
©2019 Crestron Electronics, Inc.
Crestron Electronics, Inc.
Quick Start - Doc. 8405B
15 Volvo Drive, Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
Specifications subject to
www.crestron.com
change without notice.
(2052788)
04.19
Advertisement
