Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Siemens LE 64130
Summary of Contents for Siemens LE 64130
- Page 1 Instructions for use LE 64130 LE 62031...
- Page 2 ELECTR. min. min. min. min.
-
Page 3: Appliance Description
Instructions for Use Appliance description Operating modes If the air intake is inadequate, there is a risk of poisoning from combustion gases which are drawn back into the room. An air-intake/exhaust-air wall box by itself is no guarantee that the limiting value will not be exceeded. -
Page 4: Before Using For The First Time
Before using for the first time Important notes: Before using your appliance for the first time, please read these Instructions for The Instructions for Use apply to several Use carefully. They contain important versions of this appliance. Accordingly, information concerning your personal you may find descriptions of individual safety as well as on use and care of the features that do not apply to your... -
Page 5: Using The Extractor Hood
Using the extractor hood Kitchen vapour is most effectively Switching on the extractor hood eliminated by: when you start cooking. Switching off the extractor hood few minutes after you have finished cooking. Light Fan speed Switching on the fan: Open the door. Select fan speed. -
Page 6: Filters And Maintenance
Filters and maintenance Different grease filters can be used to absorb the grease particles in kitchen vapour. Fleece grease filter: Metal grease filters: The filter mat consists of highly The filter mats consist of non-flammable flameresistant material. metal. Attention: Attention: A build up of greasy residue increases A build up of greasy residue increases flammability, and the function of the... - Page 7 Filters and maintenance Removal the grease filter: Fitting grease filters: Open door as far as it will go. Clamp in the filter mats with the wire grid. 2. Push the filter screen up slightly, lift it towards you over the brackets and take it out downwards..
-
Page 8: Activated Carbon Filter
Filters and maintenance Activated carbon filter: 5. Insert activated carbon filter in the lower left corner of the housing. Shift it until For binding odours in recirculating air both hooks slot into the holes and then mode. secure in place with the wing nut. Fitting and removal: Open door to the stop. -
Page 9: Cleaning And Care
Cleaning and care Changing the bulbs Isolate the extractor hood by pulling out 1. Switch off the extractor hood and the mains plug or switching off the fuse. deenergize by pulling out the mains plug or switching off the fuse. When cleaning the grease filters, remove 2. -
Page 10: Before Installation
Installation instructions Important information Before installation Optimum efficiency of the extractor Old appliances are not worthless rubbish. Valuable raw materials can be hood: reclaimed by recycling old appliances. Short, smooth exhaust pipe. Before disposing of your old appliance, render it unusable. As few bends as possible. -
Page 11: Exhaust-Air Mode
Before installation Exhaust-air mode If the air intake is inadequate, there is a The exhaust air is discharged upwards risk of poisoning from combustion through a ventilation shaft or directly gases, which are drawn back into the through the outside wall into the open. room. -
Page 12: Circulating-Air Mode
Before installation With exhaust mode Connecting to Ø150 mm exhaustair duct , a backwash valve should be installed unless it is already in- Attach the enlarging adapter (enclosed or corporated in the exhaust pipe or wall box. available from specialist dealer) to the air outlet. -
Page 13: Electrical Connection
Electrical connection WARNING: Length of the connection cable: 1.30 m. THIS APPLIANCE MUST BE EARTHED If permanent connection is required: IMPORTANT: Fitting a Different Plug: The extractor hood may only be connected by an electrician registered with the local The wires in the power cord are electricity board. -
Page 14: Mounting The Door
Installation The extractor hood can also be installed Important : If the door of the unit is at a slightly lower, depending on the height of distance from the body of the unit (e.g. due the wall cupboards. Position the template to rubber stops), the extractor hood must correspondingly lower. - Page 15 Installation 2. Mark the fixing points on the door. For 5. The two screws to the right and left dimensions of vertical screw fixings, see: inside the housing can be used to adjust door gliding according to the weight of the door.
- Page 16 LZ23000 LZ62010 LX3000 086244 088208 LZ65010 9000 022956...