Table of Contents
Advertisement
Connecting appliances via your home network
Use this type of connection if neither or one of the two
appliances is connected to the Home Connect app.
If the appliances are connected to each other via your
home network, you can use both the hood controls and
Home Connect to operate the hob.
Notes
Make sure you follow the safety instructions in the
■
instruction manual for your extractor hood and that
these are complied with even when operating the
appliance via the hood controls on the
hob.~ "Important safety information" on page 5
If the appliance is being operated by means of the
■
controls on the extractor hood, this mode of
operation always has priority. It is not possible to use
the hood controls on the hob during this time.
In networked standby mode, your appliance requires
■
a maximum of 2 W.
Setting up
To set up the connection between the hob and the
extractor hood, the hob must be switched on.
Connecting directly
Make sure that the extractor hood is switched off.
For more information refer to the section entitled
"Connecting to the hob" in the instruction manual for
your extractor hood.
If you connect your hob directly to the extractor
Note:
hood, it cannot be connected to your home network as
well and you will not be able to use Home Connect.
Switch on the hob.
1.
Touch and hold the
2.
The product information is displayed.
Touch the
symbol repeatedly until the
0
3.
setting appears.
lights up in the hotplate display.
‹
Set the value
‚
in the settings area.
4.
flashes in the hotplate display.
‚
You have two minutes to initiate the connection
5.
process on the extractor hood.
Once the hob is connected to the extractor hood, the
value
appears in the hotplate display. After you exit
„
the settings menu, the symbols for the hob-based hood
controls are displayed in the hob's control panel.
symbol for four seconds.
0
™‚‡
Connecting via your home network
You require a router that has WPS functionality.
You require access to your router.If you do not have
this, follow the steps for "Direct connection".
When you begin, make sure that the extractor hood is
connected to the app or is on your home network.
Switch on the hob.
1.
Touch and hold the
2.
The product information is displayed.
Touch the
symbol repeatedly until the
0
3.
setting appears.
(not connected) or
‹
network) will be lit on the hotplate display.
Set the value
in the settings area.
‚
4.
flashes in the hotplate display.
‚
If the appliance is not yet connected to your home
5.
network, press the WPS button on the router within
the next 2 minutes.
The hob will be connected to your home network
and the value
will appear on the hotplate display.
ƒ
The process of connecting to the extractor hood
starts automatically and is active for 2 minutes.
If the appliance is already connected to your home
network, proceed to the next step.
Initiate the process for connecting to the extractor
6.
hood.
Once the hob is connected to the extractor hood, the
value
appears in the hotplate display. After you exit
„
the settings menu, the symbols for the hob-based hood
controls are displayed in the hob's control panel.
Connection can only be established when both
Note:
appliances are connected to your home network and
the connection process has been initiated for both of
them. If the connection process has already timed out
for one of the two appliances, try to connect again
(basic settings,
setting).
™‚‡
Disconnecting from the network
Y ou can reset the connections you have saved for your
D i s c o n n e c t i n g f r o m t h e n e t w o r k
home network and extractor hood at any time.
Switch on the hob.
1.
Touch and hold the
2.
The product information is displayed.
Touch the
symbol repeatedly until the
0
3.
setting appears.
Set the
value on the control panel.
‹
4.
The connection has been restored.
Hood connection
symbol for four seconds.
0
™‚‡
(connected to home
ƒ
symbol for four seconds.
0
™‚‡
en
31
Advertisement
Table of Contents
