ABB RELION 670 Series Commissioning Manual page 10

Table of contents
10.4.8 High Speed distance for series compensated line zones, quadrilateral and mho
characteristic ZMFCPDIS .........................................................................................................101
10.4.8.1 Measuring the operating limit of set values.....................................................................104
10.4.8.2 Measuring the operating time of distance protection zones.......................................104
10.4.8.3 Completing the test...............................................................................................................105
10.4.9 Power swing detection ZMRPSB ........................................................................................... 105
10.4.9.1 Verifying the settings............................................................................................................106
10.4.9.2 Testing the power swing detection function ZMRPSB ..................................................107
10.4.9.3 Testing the
10.4.9.4 Testing the block input, interaction between FDPSPDIS or FRPSPDIS
and ZMRPSB ........................................................................................................................... 107
10.4.9.5 Completing the test.............................................................................................................. 108
10.4.10 Power swing logic PSLPSCH................................................................................................... 108
10.4.10.1 Testing the carrier send and trip signals.......................................................................... 108
10.4.10.2 Testing the influence of the residual overcurrent protection...................................... 109
10.4.10.3 Checking the underreaching zone...................................................................................... 109
10.4.10.4 Completing the test.............................................................................................................. 109
10.4.11 Pole slip protection PSPPPAM................................................................................................ 109
10.4.11.1 Verifying the settings............................................................................................................ 110
10.4.11.2 Completing the test............................................................................................................... 112
10.4.12 Out-of-step protection OOSPPAM......................................................................................... 112
10.4.12.1 Verifying the settings.............................................................................................................113
10.4.12.2 Test of point RE (R
10.4.12.3 Test of the boundary between zone 1 and zone 2, which is defined by the
parameter
10.4.12.4 Test of the point SE (R
10.4.13 Automatic switch onto fault logic ZCVPSOF........................................................................127
10.4.13.1 Activating ZCVPSOF externally............................................................................................128
10.4.13.2 Initiating ZCVPSOF automatically and setting mode to impedance...........................128
10.4.13.3 Initiating ZCVPSOF automatically and setting mode to UILevel ................................. 128
10.4.13.4 Completing the test...............................................................................................................128
10.4.14 Phase preference logic PPLPHIZ ............................................................................................128
10.4.14.1 Completing the test...............................................................................................................129
10.5 Current protection......................................................................................................................... 129
10.5.1 Instantaneous phase overcurrent protection 3-phase output PHPIOC ........................ 129
10.5.1.1 Measuring the operate limit of set values.........................................................................130
10.5.1.2 Completing the test...............................................................................................................130
10.5.2 Four step phase overcurrent protection 3-phase output OC4PTOC.............................. 130
10.5.2.1 Verifying the settings............................................................................................................ 130
10.5.2.2 Completing the test............................................................................................................... 131
10.5.3 Instantaneous residual overcurrent protection EFPIOC ................................................... 131
10.5.3.1 Measuring the operate limit of set values......................................................................... 131
10.5.3.2 Completing the test............................................................................................................... 132
10.5.4 Four step residual overcurrent protection, (Zero sequence or negative sequence
directionality) EF4PTOC .......................................................................................................... 132
10.5.4.1 Four step directional earth fault protection..................................................................... 132
4
tR1 timer............................................................................................................. 107
, X ).............................................................................................116
FwdR FwdX
ReachZ1 ................................................................................................................ 120
, X )........................................................................................123
RvsR RvsX
Commissioning manual