Samsung VP-D361W Service Manual page 164

Operating Instructions
Preparation
Lithium Battery Installation
Lithium Battery Installation for the Internal Clock
1. Remove the Battery Pack from the rear of the Camcorder.
2. Open the Lithium Battery Cover on the rear of the Camcorder.
3. Position the Lithium Battery in the Lithium Battery Holder, with the positive
( ) terminal face up.
Be careful not to reverse the polarity of the Battery.
4. Close the Lithium Battery Cover.
Lithium Battery Installation for the Remote Control (VP-D363(i)/D364W(i)/D365W(i) only)
1. Pull out the Lithium Battery Holder toward the direction of the arrow
using instruments such as a pair of tweezers.
2. Position the Lithium Battery in the Lithium Battery Holder, with the positive
( ) terminal face up.
3. Reinsert the Lithium Battery Holder.
Precaution regarding the Lithium Battery
1. The Lithium Battery maintains the clock function and preset contents of the memory; even if the Battery Pack or
AC Power adapter is removed.
2. The Lithium Battery for the Camcorder lasts about 6 months under normal operation from time of installation.
3. When the Lithium Battery becomes weak or dead, the date/time indicator will display <00:00 1.JAN.2006> when you
set the <Date/Time> to <On>.
When this occurs, replace the Lithium Battery with a new one (type CR2025).
4. There is a danger of explosion if Battery is incorrectly replaced.
Replace only with the same or equivalent type.
Warning: Keep the Lithium Battery out of reach of children. Should a battery be swallowed, consult a doctor
immediately.
ENGLISH
Preparation
Using the Lithium Ion Battery Pack
✤ Use SB-LSM80 or SB-LSM160 Battery Pack only.
✤ The Battery Pack may be charged a little at the time of purchase.
Charging the Lithium Ion Battery Pack
1. Turn the [Power] switch to [Off].
2. Attach the Battery Pack to the Camcorder.
3. Connect the AC Power Adapter to an AC Cord and
connect the AC Cord to a wall socket.
4. Connect the DC cable to the DC jack on the
Camcorder. The charging indicator will start to blink,
showing that the Battery is charging.
5. Press and hold the DISPLAY button while charging and the charging status will be
displayed on the LCD for 7 seconds.
■ As indicated the battery level is given as reference data for the user, it is the
approximate estimation. It may differ from Battery capacity and temperature.
6. When the Battery is fully charged, disconnect the Battery Pack and the AC Power Adapter
from the Camcorder.
Even with the Power switched Off, the Battery Pack will still discharge.
Charging, Recording Times based on
Model and Battery Type.
✤ If you close the LCD Screen, it switches off and
the Viewfinder switches on automatically.
✤ The continuous recording times given in the table
to the right are approximations.
Actual recording time depends on usage.
✤ The continuous recording times in the operating
instructions are measured using a fully charged Battery Pack at 77 °F (25 °C).
✤ Even when the Power switched Off, the Battery Pack will still discharge if it is left attached to the device.
16 16
11-4
All manuals and user guides at all-guides.com
Once per second
Twice per second
Three times per second
Blinking stops and stays on
On for a second and
off for a second
Battery
SB-LSM80
SB-LSM160
(Option)
QUICK
MENU
MENU
CHG
Blinking time Charging rate
Less than 50%
50% ~ 75%
75% ~ 90%
90% ~ 100%
Error - Reset the Battery Pack and
the DC Cable
Battery Info
Battery c c harged
0%
Time Recording time
Charging
time
LCD On
Approx.
Approx.
1hr 20min 1hr 20min
Approx. Approx.
2hr 40min
3hr
ENGLISH
15 15
50% 100%
Viewfinder On
Approx.
1hr 30min
Approx.
3hr
Samsung Electronics