CABINETS TO GO Findley & Myers DC312 Assembly Instructions Manual
3 drawer base cabinets & vanity drawer cabinets
Hide thumbs
Also See for Findley & Myers DC312:
- Assembly instructions (5 pages) ,
- Assembly instructions manual (8 pages)
Advertisement
Quick Links
ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all
3 Drawer Base Cabinets & Vanity Drawer Cabinets
ITEM# DC312, DC315, DC318, DC321, DC324, DC327,
DC330, DC333, DC336 VDC12, VDC15, VDC18 VDC21,
VDC24, VDC27, VDC30, VDC33, VDC36
Page 1
Advertisement
Related Manuals for CABINETS TO GO Findley & Myers DC312
Summary of Contents for CABINETS TO GO Findley & Myers DC312
- Page 1 ASSEMBLY INSTRUCTIONS These assembly instructions are only applicable for all 3 Drawer Base Cabinets & Vanity Drawer Cabinets ITEM# DC312, DC315, DC318, DC321, DC324, DC327, DC330, DC333, DC336 VDC12, VDC15, VDC18 VDC21, VDC24, VDC27, VDC30, VDC33, VDC36 Page 1...
-
Page 2: General Instructions
►General Instructions: Thank you for purchasing a Cabinets To Go product. You are now the proud owner of a high quality product designed to face the test of daily use and guaranteeing your enjoyment for many years to come. Carefully read the instructions before starting the installation. During assembly, please follow all generally accepted safety procedures. Failure to adhere to the following instructions will invalidate the warranty and Cabinets To Go will decline any responsibility for any damages caused. Any installation which does not correspond to the instructions may result in defects, malfunctioning parts, significant damage and/or injury. Before the assembly begins, check that all appropriate and required plumbing and electrical connections exist. Before drilling, make absolutely sure that there are no pipes (gas, water,electricity, heating, etc.) at the drilling location. Cabinets To Go will not be held responsible for failure to follow these instructions. PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT 1-800- CABINET. - Page 3 Assemble the Side Panels (A,B) onto the Frame (E) by connecting the male and female cam locks and using a screwdriver to turn the lock clockwise. (Figure 1) { NOTE: Lay Frame and Doors on a flat smooth soft work surface to assemble. } Figure 1 Install the glide brackets (e) to the Back Panel (C)
- Page 4 Insert the Bottom Panel (D) into the groove of the Side Panels and Frame. (Figure 3) Figure 3 Install the toe kick (F) onto the side panels (A,B) and lock the cam locks. (Figure 4) Figure 4 Page 4...
- Page 5 Install the Back Panel (C) onto the side panels (A,B) and lock the cam locks. (Figure 5) Figure 5 Attach the Drawer Glides (G) using screws (c) onto the frame and glide brackets installed in Step 2. (Figure 6) Figure 6 Page 5...
- Page 6 Assemble the drawer front (H) onto the drawer box front using the supplied screws (b). Place bumpers (d) onto the corners of the drawer front. (Figure 7) Figure 7 Finish assembling the drawer boxes. (H) (Figure 8) { NOTE: You may use a rubber mallet if needed to seat the dove tails.
- Page 7 Attach the Drawer Clips (f) using screws (c) onto the bottom of the drawers. (H) (Figure 9) Figure 9 Assemble the drawer front (I) onto the drawer box front using the supplied screws (b). Place bumpers (d) onto the corners of the drawer front.
- Page 8 Finish assembling the drawer boxes. (I) (Figure 11) { NOTE: You may use a rubber mallet if needed to seat the dove tails. } Optional Tools: Rubber Mallet Figure 11 Attach the Drawer Clips (f) using screws (c) onto the bottom of the drawers.
- Page 9 Install the corner brackets (a) using screws (c) in the four top corners. (Figure 13) Figure 13 Insert the assembled drawers (H,I) onto the glides. Push in until you hear clicks from the drawer clips locking into the glides. (Figure 14) Figure 14 Page 9...
-
Page 10: Maintenance
►Maintenance For daily cleaning, use a dry cloth and a soft liquid cleaner. Never use abrasive cleaners containing acetone, chlorine or strong bleach. Also, do not use tools as scrapers, metallic brushes, and other products which can scratch or tarnish surfaces. Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets etc.