Parts Description; Installation - Makita DCX200 Instruction Manual

14. During and after use, the battery cartridge may
take on heat which can cause burns or low
temperature burns. Pay attention to the han-
dling of hot battery cartridges.
15. Do not touch the terminal of the tool imme-
diately after use as it may get hot enough to
cause burns.
16. Do not allow chips, dust, or soil stuck into the
terminals, holes, and grooves of the battery
cartridge. It may cause heating, catching fire,
burst and malfunction of the tool or battery car-
tridge, resulting in burns or personal injury.
17. Unless the tool supports the use near
high-voltage electrical power lines, do not use
the battery cartridge near high-voltage electri-
cal power lines. It may result in a malfunction or
breakdown of the tool or battery cartridge.
18. Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causing fires, personal injury and damage. It will
also void the Makita warranty for the Makita tool and
charger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4. When not using the battery cartridge, remove
it from the tool or the charger.
5. Charge the battery cartridge if you do not use
it for a long period (more than six months).

PARTS DESCRIPTION

► Fig.1
1 Power button
3 Plug
Optional accessory
► Fig.2
1 Battery holder for CXT
battery cartridge
3 Battery BL1055B
(Country specific)
5 LXT battery cartridge
(14.4 V / 18 V)
2 Battery pocket
- -
2 Battery holder for LXT
battery cartridge
4 CXT battery cartridge
(10.8 V - 12 V max)
- -

INSTALLATION

Charging the battery
Battery cartridges used with battery holder
Refer to the instruction manual of the charger for how to
charge the battery.
Battery BL1055B
Open the cover on the USB port. Connect the battery
and AC Power Adapter ADP07 (not included) or other
general USB charger using the USB cable supplied with
the battery. The recommended output spec for general
USB charger is 5 V / 3 A or lower. After that, plug the AC
Power Adapter ADP07 to the mains. When the charging
is finished, all battery capacity indicator will light up
and then turns off after a certain period. Unplug the AC
Power Adapter and disconnect the USB cable, and then
close the cover.
► Fig.3: 1. AC Power Adapter ADP07
2. Battery BL1055B 3. Cover 4. USB cable
Meaning of the indicator lamp
Indicator lamps
Lighted
(The lamps go off after a certain period.)
Installing or removing the battery
cartridge
Only when using the battery cartridge used with
battery holder
CAUTION:
Always switch off the device
before installing or removing the battery
cartridge.
CAUTION:
Hold the battery holder and the
battery cartridge firmly when installing or remov-
ing the battery cartridge. Failure to hold the battery
holder and the battery cartridge firmly may cause
them to slip out of your hands and result in damage
to the battery holder and battery cartridge and/or a
personal injury.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator as
shown in the figure, it is not locked completely.
9 ENGLISH
Off Blinking
(The charging
Remaining
capacity
100%
is finished)
50% to 100%
25% to 50%
Less than
25%