ELNA 2000 Series Manual
  1. Manuals
  2. Brands
  3. ELNA Manuals
  4. Sewing Machine
  5. 2000 Series
  6. Manual

ELNA 2000 Series Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

IMPORTANT SAFETY INSTRUCTIONS
Your Elna 2000 series sewing machine is designed and constructed for HOUSEHOLD use only. Read
DANGER
– To reduce the risk of electric shock:
1. Your sewing machine should never be left unattended when plugged in. Always unplug the machine from
the electrical outlet immediately after using and before cleaning.
2. Always unplug before replacing light bulb. Replace bulb with same bayonet socket type, 15W max.
3. Do not place or store machine where it can fall or be pulled into a tub or sink. Do not reach for the ma-
chine if it has fallen into water. Unplug immediately.
WARNING
1. Do not allow machine to be used as a toy. Supervision is necessary when this machine is used by or
near children.
2. Use this sewing machine only for its intended use as described in this manual. Only use attachments
recommended by the manufacturer as described in this manual.
3. Never operate this machine if it has a damaged cord or plug, is not working properly, has been dropped
or damaged or dropped into water. Return the machine to the nearest authorized dealer or service center
for examination, repair, electrical or mechanical adjustment.
4. This machine is equipped with a special connection cord which, if damaged, must be replaced by an
identical cord. This can be obtained from your dealer.
5. Never operate the sewing machine with any air opening blocked. Keep ventilation openings of the sew-
ing machine and foot control free from the accumulation of lint, dust and fibers.
6. Never drop or insert any object into any opening.
7. Do not use outdoors.
8. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
9. To disconnect, turn machine off and remove plug from outlet.
10. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
11. Keep fingers away from all moving parts, especially the needle.
12. Always use the proper needle plate. The wrong plate can cause the needle to break.
13. Do not use bent needles.
14. Do not pull or push fabric while stitching. This may deflect the needle causing it to break.
15. Switch the sewing machine off when making any adjustment in the needle area, such as threading
needle, changing needle, threading bobbin, changing presser foot, etc.
16. Always unplug the sewing machine from the electrical outlet when removing covers, lubricating or mak-
ing any other servicing adjustments mentioned in the instruction manual.
USA only
Your machine comes equipped with a polarized plug (one prong wider than the other). A polarized plug re-
duces the risk of electrical shock. This plug is intended to fit into a polarized outlet. If the plug does not fit
fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper
outlet. Do not modify the plug in any way.
Use only foot control YC-482J or TJC-150 (UL, CSA).
all instructions before using this machine.
– To reduce the risk of burns, fire, electrical shock or injury:
SAVE THESE INSTRUCTIONS
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 2000 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ELNA 2000 Series

Summary of Contents for ELNA 2000 Series

  • Page 1 IMPORTANT SAFETY INSTRUCTIONS Your Elna 2000 series sewing machine is designed and constructed for HOUSEHOLD use only. Read all instructions before using this machine. DANGER – To reduce the risk of electric shock: 1. Your sewing machine should never be left unattended when plugged in. Always unplug the machine from the electrical outlet immediately after using and before cleaning.

  • Page 2: Table Of Contents

    NOTE: Information found in this instruction Zipper Insertion ..........20-21 Pintucks ..............22 manual is current at the time of printing. Elna Twin Needle Hem (Optional needle) ....23 reserves the right to change and update specifi- cations and information as needed.

  • Page 3: Machine Parts And Functions Part Names

    SECTION 1 Machine Parts and Functions 13 14 15 Part Names 1. Extension table (accessory storage box) 2. Centimeter/inch measurements 3. Bobbin cover 4. Needle plate 5. Circular sewing pivot points 6. Presser foot 7. Presser foot release lever 8. Thread cutter 9.

  • Page 4: Extension Table (Accessory Storage Box) And Free Arm

    Extension Table (Accessory Storage Box) and Free Arm Extension Table The extension table provides more sewing space to make sewing easier. The extension can be easily removed for free arm sewing. Free arm sewing is good for circle areas like sleeves, waistbands and pant legs.

  • Page 5: Additional Presser Foot Clearance

    Additional Presser Foot Clearance You can raise the presser foot higher than the nor- mal up position for easy removal of the presser foot or to place heavy fabrics under the presser foot. Pull the presser foot lever up beyond the normal up posi- tion.

  • Page 6: Seam Allowance Lines

    Seam Allowance Lines The lines on the needle plate help you measure seam width. The number shows you the space between the cen- ter needle position and the line on the needle plate. The numbers at the front are in millimeters. The numbers at the back are in inches.

  • Page 7: Stitch Length Knob

    Stitch Length Knob Turn the stitch length knob. The lower the number, the shorter the stitch length. The higher the number, the longer the stitch length. Each stitch will have a suggested length range. Fine Tuning Stretch Stitches If the stretch stitch doesn’t look right, you can adjust it.

  • Page 8: Thread Tension Dial

    Thread Tension Dial Straight Stitch In straight seams, the needle thread and the bobbin thread should lock together in the center of the two layers of fabric. If you look at the top and bottom of the stitch, you will notice that there are no gaps; each stitch is smooth and even.

  • Page 9: Getting Ready To Sew

    SECTION II Getting Ready to Sew Selecting the Correct Needle and Thread Needle Weight Needle Type Fabric Size There are many kinds of fabrics, threads and Very Universal 9 (65) Chffon, Fine Lace, Light Ball Point 9 (65) Organdy needles. It is important to use the correct ones to- gether.

  • Page 10: Needle Definitions

    Needle Definitions The illustration identifies the main parts of a sewing machine needle. 1. Body 2. Shaft 3. Long groove (round side of needle) 4. Short groove (flat side of needle) 5. Eye 6. Point Universal – an all-purpose needle that handles most woven and knit fabrics.

  • Page 11: Connecting The Machine To Power Supply

    Connecting the Machine to Power Supply Your machine is equipped with a detachable power cord. Before connecting the power cord, make sure the voltage and frequency shown on the machine are identical to your electrical power. Check that the power/light switch is in the off posi- tion.

  • Page 12: Foot Control And Sewing Speed

    Foot Control and Sewing Speed Sewing speed is determined by how hard you press on the foot control. The harder you press on the foot control, the faster the machine runs. IMPORTANT: Before using your sewing machine (U.S.A.) the first time, place waste fabric under the presser foot and run the machine without thread for a few minutes.

  • Page 13: Winding A Bobbin

    Winding a Bobbin 1. Pull out the flywheel to keep the needle from moving up and down. 2. Place the spool of thread on the spool pin with the thread coming off the spool as shown. Pull the thread over around the bobbin winder thread guide.

  • Page 14: Inserting The Bobbin

    Inserting the Bobbin 1. Place the bobbin in the bobbin case. Make sure the thread unwinds in the direction shown in the illustration. 2. Pull the thread into the bobbin case slot. 3. Draw the thread under the tension spring and into the delivery eye.

  • Page 15: Threading The Machine

    Threading the Machine Turn the flywheel toward you to raise the needle to its highest position. Raise the presser foot. Pull the thread under the thread guide. Guide the thread down the right side slot into the tension area, continuing down around the check spring holder.

  • Page 16: Drawing Up The Bobbin Thread

    Drawing Up the Bobbin Thread 1. Raise the presser foot and hold the needle thread lightly with your left hand. 2. Turn the flywheel towards you to lower needle into machine. Continue turning until the needle has risen and the take-up lever is at its highest position.

  • Page 17: Sewing Basics

    SECTION III Sewing Basics Example Of How To Read the Machine Set- Up Information Set Stitch Selection Knob Set stitch selection knob on straight stitch. Set Stitch Length Knob Set stitch length knob according to fabric weight (see page 18). Set Thread Tension Dial Set thread tension to 4.

  • Page 18: Straight Stitch

    Straight Stitch The straight stitch is used to sew a seam in woven fabrics and may also be used for gathering, basting, sewing in a zipper, pintucks, rolled hems and twin needle hems. NOTE: Fine fabrics should have a stitch length be- tween 1.5 and 2.5, medium fabrics between 2.0 and 3.0 and heavier fabrics between 3.0 and 4.0.

  • Page 19: Gathering

    Gathering Gathering/shirring evenly distributes fullness in an area with very tiny pleats. Gathering is one row or two parallel rows. Shirring is three or more parallel rows. Light to medium weight fabrics provide the best results. Decrease tension to 2.0 – 4.0. Increase stitch length to 4.

  • Page 20: Zipper Insertion

    Zipper Insertion (Model 2100 – optional foot) • Lapped Application Lapped zippers are usually inserted into a side seam of skirts or pants, for example. Attach the pin on the zipper foot to the groove on the shank. • To sew the left side of the zipper, attach the zip- per foot on the right-hand side.
  • Page 21 Stop just before the zipper foot reaches the slider on the zipper tape. Lower the needle slightly into the fabric. Raise the zipper foot and open the zipper. Lower the foot and stitch the remainder of the seam. Close the zipper and spread the fabric flat with the right side facing up.

  • Page 22: Pintucks

    Pintucks Pintucks should be added to your fabric before cut- ting out the pattern piece. 1. Use a washable fabric marker and draw lines for pintucks on the fabric right side. 2. Fold the fabric together on the first line with wrong sides together.

  • Page 23: Twin Needle Hem (Optional Needle)

    Twin Needle Hem (optional needle A twin needle hem is quick and easy. It is especially useful for very stretchy fabrics. Be sure to use a stretch twin needle for knit fabrics. CAUTION: Center based twin needles are available in many different sizes and widths. Before sewing, always turn the flywheel to make sure the needles do not hit the foot.

  • Page 24: Whip And Roll Hem

    Whip and Roll Hem (Model 2100 – optional foot) This technique makes a beautiful edge on ruffles and hems. It should only be used for lightweight fabrics. 1. The fabric edge must be clean cut with no unrav- eling threads. 2.

  • Page 25: 3-Step Zigzag

    3-Step Zigzag The 3-step zigzag (sometimes called a multiple zig- zag) is used to finish raw seam edges. This stitch gives a flatter edge finish than the regular zigzag. It is also used for mending tears in fabric. Place the fabric under the presser foot so the needle swings off the fabric to the right or trim away any excess fabric.

  • Page 26: Stretch Blind Hem Or Woven Blind Hem

    Woven Blind Hem (#4) (2300 only) The blind hem may be used to sew a blind hem on either knit or woven fabrics. Elna invented the stretch blind hem in 1952. Finish the raw hem edge with a zigzag or 3-step zig- zag before sewing the blind hem.

  • Page 27: Shell Tuck

    Shell Tuck (Model 2100 – optional foot) This is a pretty hem finish for lingerie and tricot fab- rics. May also be used for decorative rows of stitching. Use a lightweight fabric such as tricot. Fold and stitch on the bias. Set the stitch width and length as you desire.

  • Page 28: Picot Stitch

    Picot Stitch The picot stitch may be used to sew fabrics together “edge-to-edge”. 1. Fold and press under the seam allowance to wrong side of fabric on both fabric edges. 2. With the fabric right side up, place the folded edges next to each other under the middle of the presser foot.

  • Page 29: Automatic Buttonhole (Model 2300 Only)

    Automatic Buttonhole (Model 2300 Only) All buttonholes should use interfacing that is the same weight as the fabric. Interfacing is especially important when sewing on stretch fabrics. Always make a test buttonhole on extra fabric before sewing on your garment. Use a shorter stitch length for finer fabrics .
  • Page 30 4.. Mark the buttonhole area on the fabric. Place both threads to the left under the foot. Insert the garment under the foot and turn the flywheel until the needle comes down into the fabric. The needle should go in exactly at the marked line for the buttonhole.

  • Page 31: 4-Step Buttonhole (Model 2100 Only)

    4-Step Buttonhole Model 2100 Only) All buttonholes should use interfacing that is the same weight as the fabric. Interfacing is especially important when sewing on stretch fabrics. Always make a test buttonhole on extra fabric before sewing on your garment. Use a shorter stitch length for finer fabrics .

  • Page 32: Corded Buttonhole

    Corded Buttonhole Corded buttonholes are found on coats and other garments that require extra strong buttonholes. The cording reinforces and accentuates the buttonhole. With the buttonhole foot raised, hook the filler cord on the spur at the back of the buttonhole foot. Bring the ends forward under the buttonhole foot.

  • Page 33: How To Sew On A Button

    How To Sew On a Button (Model 2100 – optional foot) Hand sewing buttons to a garment is very time-con- suming. Sew them on in one quick, easy step. Drop the feed dog. See page 6. 2. Place the button on the fabric and turn the fly- wheel to lower the needle into a hole of the but- ton.

  • Page 34: Stretch Stitches Triple Seam

    This stitch can also be used for topstitching. Elna invented this stitch in 1952. Using a straight stitch (stitch length 4), baste a seam together. Verify the fit. Reset the machine for triple seam and sew.

  • Page 35: Smocking

    Smocking Smocking is a delicate, decorative treatment on children’s clothing or women’s blouses. Choose a soft, lightweight fabric such as batiste, gingham or challis. Cut the fabric three times the finished width. 13mm 1. Set needle thread tension to 2.5. Use the straight stitch with the stitch length at 4.0.

  • Page 36: Super Stretch Stitch

    Super Stretch Stitch This stitch is recommended for sewing fabrics such as swimwear and stretch velour as it provides the greatest amount of stretchability and strength. Seams lie flat and do not lose their shape. Foot pres- sure may need to be lowered for fabric to maintain its shape.

  • Page 37: Satin Stitches

    SECTION V Satin Stitches (Model 2300 only) Express your creative talents by using one of the pretty satin stitches to add a decorative accent. It is very important to use a stabilizer with your fabric or the stitch will not form correctly. The weight of the stabilizer should be the same as the fabric.

  • Page 38: Taking Care Of Your Machine

    SECTION VI Taking Care of Your Machine The area around the bobbin, hook and feed dog must be cleaned each time the machine has been used a lot. Clean the outside of the machine with a soft cloth and pure soap. Cleaning the Bobbin Case and Hook Loose threads and dust may cause puckered stitches and thread breakage during stitching.

  • Page 39: Cleaning The Feed Dog

    Cleaning the Feed Dog Unplug the machine. Remove the needle and presser foot. Remove the needle plate set screws and the needle plate. With a brush, clean out dust and lint clogging the feed dog teeth. Attach the needle plate. Replace needle and presser foot.

  • Page 40: Troubleshooting

    TROUBLESHOOTING Condition Cause See page(s) 1. Threads have been caught in the hook area. The machine is noisy and does not run 2. The feed dog is packed with lint. smoothly. The needle thread 1. The needle is not threaded properly. breaks.

  • Page 41: Index

    INDEX Multiple Zigzag ..........25 Accessories ............ 3 Accessory Box ........... 3, 4 Applique ............24 Needle Position ........7, 17 Automatic Buttonhole ......29-30 Needles ............. 9-10 Bobbin Oil & Oiling ..........12, 39 Drawing Up Bobbin Thread ....16 Overcasting ..........

Table of Contents

Save PDF