Fishman LOUDBOX MINI - 60W Amplifier Manual

Important Safety Instructions

Risk of electric shock. Do not open.

No user serviceable parts inside. Refer servicing to qualified personnel. Do not expose to rain or moisture.

Whenever this symbol appears, it alerts you to the presence of important operating and maintenance (servicing) instructions in the user's manual for this amplifier.

Wherever this symbol appears, it alerts you to the presence of uninsulated dangerous voltage inside the enclosure that may be sufficient to constitute a risk of shock.

To ensure your personal safety and the safety of others, operate this apparatus only after reading these instructions and heeding the warnings listed below.

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block the ventilation openings. Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at the plugs, convenience receptacles and the point where they exit from the apparatus.
11. Use only attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as a power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. Do not expose the apparatus to dripping or splashing liquids and do not place objects filled with liquids (such as a beverage container or a vase) on the apparatus.
16. Warning" To reduce the risk of fire or electric shock, do not expose this apparatus to moisture.
17. The device is designed and evaluated under the condition of non-tropical climate; and, it can be only used in locations in non-tropical climate areas. Using the device in tropical climate areas would result in high safety risk.
18. Normal operating environmental temperature range: 0°C [32°F] to 35°C [95°F].
19. 
    The battery (battery or batteries or battery pack) shall not be exposed to excessive heat such as sunshine, fire or the like.
20. 
    Danger of explosion if battery is incorrectly replaced. To replace battery use Fishman's approved battery kit only at Certified Service Centers
21. No naked flame sources, such as lighted candles, should be placed on the apparatus.
22. Do not install this equipment in a confined or building-in space such as a book case or similar unit, and remain a well ventilation conditions at open site. The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, table-cloths, curtains etc.

The mains plug/appliance coupler is used as disconnect device, the disconnect device shall remain readily operable.

Copyright © 2018 FISHMAN TRANSDUCERS, INC.
All rights reserved. No part of this document may be reproduced in any form without the written permission of FISHMAN TRANSDUCERS, INC.

Getting Started

Your new Loudbox Mini is a portable amplifi er designed to faithfully reproduce the sound of acoustic instruments and a diverse assortment of vocal or recorded accompaniments.

With the addition of Bluetooth^® wireless connectivity, you can now easily add backing tracks or other accompaniment to your performances.

Here are some basic setup tips to help get you going. To operate your Loudbox Mini safely, please read the entire manual, especially the Important Safety Instructions.

1. Locate the Power switch (next to the rear panel power cord terminal) and switch it off, then connect the power cord.
2. Plug the Loudbox Mini into an electrical outlet with the appropriate AC voltage.
3. Turn down the Master Volume control and turn on the Power switch. The Power Indicator should illuminate.
4. Connect your instrument to the Instrument input with a shielded ¼" cable.
5. Gradually increase the Instrument channel Gain:

• For instruments featuring active (battery-powered) onboard preamps, start with the control around 10 o'clock.
• For passive pickups, you may start with the control set much higher. It is normal to run this control near its maximum with many passive soundhole pickups.

6. Slowly raise the Master Volume to the desired level.

Front Panel

1. Instrument Input
   This 1/4" input accepts all types of passive or active acoustic pickups.
2. Phase
   Use the Phase switch to improve bass at low volume and suppress feedback at high volumes.
3. Gain
   Use the Gain knob to set the signal level for the instrument input.
4. Low
   Boost here to add weight to the sound. In general, boost bass at low volumes and cut bass at higher levels. With the dial set at 12 o'clock, the control is effectively out of the circuit.
5. Mid
   This control affects how well the instrument blends in or stands out in the mix. At loud volumes, a midrange cut will achieve a more natural sound. With the dial set at 12 o'clock, the control is effectively out of the circuit.
6. High
   Boost highs to add "air" to the sound of the instrument. With the knob set at 12 o'clock, the control is effectively out of the circuit.
7. Reverb
   Controls the amount of digital reverb in the Instrument channel.
8. Chorus
   Controls the depth of two separate chorus presets.
9. Mic Input
   Plug in a balanced microphone into this XLR input for vocal or for your instrument. The Loudbox Mini makes an excellent mini PA or vocal monitor. You may also connect an outboard preamp with balanced XLR out to this input.
10. Gain
    Use the Gain knob to set the signal level for the Microphone input.
11. Low
    Boost here to add weight to the sound. In general, boost bass at low volumes and cut bass at higher levels. With the dial set at 12 o'clock, the control is effectively out of the circuit.
12. High
    Boost highs to add "air" to the sound of the microphone. With the knob set at 12 o'clock, the control is effectively out of the circuit.
13. Reverb
    Controls the amount of digital reverb in the Microphone channel.
14. Master Volume
    Set the overall level of the Loudbox Mini with the Master Volume. In general, put the Master Volume as high as possible using less Gain (2 o'clock to 5 o'clock) to achieve the cleanest sound.
15. Power
    Lights up when the amplifi er power is on. The Power switch is located behind the amp next to the power cord socket.
16. Bluetooth^® Indicator
    This green indicator will display a medium fl ash indicating the Bluetooth^® module is ready for pairing. It will display a slow fl ash indicating the module is ready for reconnection with a previously paired device. The indicator will be on when playback is active and display a fast fl ash when playback is paused.
17. Bluetooth^® Pairing
    To pair a Bluetooth^® enabled device for the fi rst time, hold the Pairing button more than 5 seconds. You will hear an ascending tone and the Bluetooth^® Indicator will change from a slow fl ash to a fast fl ash indicating it is ready to pair. Ensure your Bluetooth^® enabled device is in pairing mode. Once paired the indicator will stop fl ashing and will allow you to stream music to the amplifi er. If the button is pressed during paired playback, the playback will be paused and the Bluetooth^® Indicator will display a fast fl ash. Press the button again to resume playback and the Bluetooth^® Indicator will return to on.

To activate Bluetooth^® for a previously paired device, hold the Pairing button for approximately 1-2 seconds (must be less than 5 seconds). An ascending tone will play briefl y to indicate the Bluetooth^® is powering on. The Bluetooth^® Indicator will slowly fl ash informing it is ready to reconnect and will pair if your device is in pairing mode.

To turn off the Bluetooth^® when already paired, hold the button for 1-2 seconds. A descending tone will indicate that the connection is powering down and the Bluetooth^® Indicator will turn off.

Rear Panel

1. AC power
   Operate the amplifi er only at the voltage indicated on the rear panel.
   For 120V amplifi ers purchased in the USA, Canada and Mexico, plug in the supplied detachable AC power cable.
   For 100V and 230V amplifi ers purchased outside the USA and Canada, you will need to supply your own detachable AC cable. This cable must have an IECstyle 320 connector at one end, and a male AC plug appropriate for your region at the other.
   Disconnect device is AC inlet or power switch.
2. Power switch
   Lower the Master Volume before you turn on the amp. Flip the power switch to the up position.
3. Aux Input - 1/4" & 1/8"
4. Aux Input - 1/4" & 1/8"
   Plug in a line level stereo audio source such as a CD or MP3 player in this input. Both inputs may be used at the same time. They are stereo (TRS) inputs, however the left and right signals are mixed to mono.
5. Mix D.I. (Post)
   Plug in here when you wish to send signals from both Channel 1 and 2 to a mixing console or a slave amplifi er. This post-EQ output is always ground isolated to prevent ground loop hum.

Tone Tips

Set up
For reference, start with the tone controls set straight-up, (twelve o'clock). In this position, there is no additional boost or cut equalization applied to your sound. Begin at a very low volume and work your way up. As you turn up, try adjusting the Loudbox Mini's tone controls as recommended below.

1. Low volume
   At a low volume (just above conversation level) our ears are not very sensitive to bass and treble, so give the Low and High controls a good boost. Try three o'clock on the dial.
   
2. Medium volume
   At medium levels, when you need to raise your voice to be heard over the music, the human ear is quite sensitive to midrange. Cut the Mid control to about ten o'clock or to your taste. At this level, our perception of bass and treble starts to catch up to the rest of the tonal spectrum, so you can back off the Low and High controls slightly for good tonal balance.
   
3. High volume
   At loud levels, when you must shout to be heard over the music, your ears (and your audience) will benefi t from a deep midrange cut. Set the Mid dial between nine and seven o'clock. Our perception of bass and treble "fl attens out" at high volumes, so you won't need much, if any, Low or High boost. Set the Low and High knobs to between twelve and one o'clock. In many cases, you can also improve the tone at very high volume if you cut bass. Try setting the Low knob between ten and eleven o'clock.
   

Block Diagram

Technical Specifications

We reserve the right to change any of the specifi cations and information in this manual without notice.