Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Macnaught Manuals
  4. Tools
  5. MAN1915-01
  6. Manual

Macnaught MAN1915-01 Manual

Oil/air/water reel
Hide thumbs
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual
MAN1915-01 (3/4")
OIL/AIR/WATER REEL
MAN Narrow Gauge Series
Heavy Duty Hose Reels
Introduction
Thank you for purchasing a Macnaught Narrow
Gauge MAN1915 Oil/Air/Water Reel.
Description
Your Macnaught Oil/Air/Water Reel has been
manufactured and constructed using high quality
materials
Important
CAUTION
PLEASE READ THIS SAFETY INFORMATION
CAREFULLY BEFORE USE.
Please read and retain this instruction manual to
assist you in the operation and maintenance of this
product.
'CAUTIONS' are listed throughout this manual to
advise of actions that may cause personal injury or
damage to your equipment.
Never exceed the pressure rating of any component
in the system. Remember this is an oil/air/water reel
which is capable of a working pressure of 1250psi.
Before operation check hoses for signs of wear,
leaks or loose fittings. Tighten all fluid connections
regularly and replace weak or damaged hose.
Check equipment daily for any leaks or damage.
Repair or replace worn or damaged items
immediately with genuine replacement parts.
DO NOT attempt to stop leaks with your hand, body
glove or rag.
If accidental injection or injury should occur,
seek IMMEDIATE emergency medical attention.
INST-MAN19 ISSUE 3 © 2017
CAUTION
Before attempting any maintenance or repairs of
this product, carefully release the fluid pressure,
before disconnecting the reel, failure to do this
may cause injury
To prevent injury or damage occurring, do not let
go of the hose during rewinding.
Installation
1) Using the appropriate hardware, bolt the frame
base of the reel to the desired location (See
Drilling Template). Ensure the mounting is strong
enough to support the weight of the reel.
2) Pull out hose to check spring tension and adjust if
required (See Adjusting Spring Tension)
3) Securely connect the fluid supply line to the reel
inlet on the side of the reel.
4) Securely connect the desired hose-end
attachment to the hose outlet.
Note: Thread sealant may be required
4) Turn on system and check for any leaks or
damage before use. Repair or reseal if required
1

Advertisement

loading

Related Manuals for Macnaught MAN1915-01

Summary of Contents for Macnaught MAN1915-01

  • Page 1 MAN1915-01 (3/4”) OIL/AIR/WATER REEL MAN Narrow Gauge Series Heavy Duty Hose Reels Introduction Thank you for purchasing a Macnaught Narrow Gauge MAN1915 Oil/Air/Water Reel. Description Your Macnaught Oil/Air/Water Reel has been manufactured and constructed using high quality materials Important CAUTION...

  • Page 2: Mounting Options

    Hose Installation Procedure Mounting Options Truck bed Remove Hose Assembly • Wall (Max 4 meter above the floor) • 1) Turn off and disconnect the supply to reel and Ceiling (Max 4 meter above the floor) • release hose line pressure. 2) Pull out approximately 2m (6ft) of hose and allow Guide arm positions: the drum to latch.
  • Page 3 Maintenance Turn the hex key clockwise (against hose roll out) to increase tension. Increase Tension 7) Remove the circlip retaining the swivel body Turn the hex key counter-clockwise (with hose roll out) to decrease tension. 8) Remove the swivel boy from the shaft. Note: Remove the hose from swivel body if required.
  • Page 4 MAN1915-01 - Diagram and Part List Order for replacement Item no Part or Set No off Description SK225s Roller mouth assembly SK223s Latch Set SK220s Swivel Assembly SK221s Swivel Seal Set RHA62s Hose Stopper RH1915HPs Hose Assembly SK224s Bearing Set...

  • Page 5: Troubleshooting

    Troubleshooting Problem Cause Remedy Hose does not fully Outlet nozzle, gun or tool is too Add spring tension (See “Adjust Spring Tension”) retract heavy Spring requires re-tensioning Add spring tension (See “Adjust Spring Tension”) Replacement hose is too long Fit correct length hose (Refer to Hose Specifications”) Hose does not retract at Spring has broke or has lost tension Replace spring canister is required Reel does not latch...
  • Page 6 Dimensional Diagrams MAN0915-01 INST-MAN19 ISSUE 3 © 2017...

  • Page 7: Drilling Template

    Drilling Template Note: Drawing Not To Scale INST-MAN19 ISSUE 3 © 2017...
  • Page 8 Note: This product should be disposed of according to all applicable local and national government environment regulations and guidelines. For Warranty Terms and Conditions see macnaught.com.au For a list of Australian Service Centres see macnaught.com.au INST-MAN19 ISSUE 3 © 2017...