Quantum LTO 1U Installation Manual
1u rackmount rail
Hide thumbs
Also See for LTO 1U:
- Reference (32 pages) ,
- Install manual (1 page) ,
- Quick start manual (36 pages)
Advertisement
Quick Links
Document 81-81209-05 A01, January 2006
Quantum 1U Rackmount
For 24-Inch Racks.......................................................................................................5
For Racks Deeper than 24 Inches.............................................................................7
Rail Installation Guide
3
3
4
5
9
11
1
Advertisement
Related Manuals for Quantum LTO 1U
Summary of Contents for Quantum LTO 1U
-
Page 1: Table Of Contents
Step 2: Installing the Stationary Sections onto the Equipment Rack For 24-Inch Racks...5 For Racks Deeper than 24 Inches...7 Step 3: Installing the 1U Rackmount into the Equipment Rack Typical Rack and Slide Configurations (For Reference Only) Document 81-81209-05 A01, January 2006 Quantum 1U Rackmount Rail Installation Guide... - Page 2 Made in the USA. Quantum Corporation provides this publication “as is” without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this publication from time to time without notice.
-
Page 3: Introduction
Introduction The Quantum Rack Mount Slide Kit is designed to facilitate the mounting of 1U Rackmount systems in standard EIA-310 equipment racks. These telescoping slide rails provide easy access to the 1U Rackmount by allowing you to unlock and slide it forward. -
Page 4: Step 1: Installing The Chassis Sections Onto The 1U Rackmount
Quantum 1U Rackmount Rail Installation Guide Document 81-81209-05 A01 January 2006 Step 1: Installing the Chassis Sections onto the 1U Rackmount Figure 1 Pressing the Release Button Figure 2 Attaching the Chassis Section to the 1U Rackmount Chassis There are two chassis sections, one for each side of the 1U Rackmount chassis. -
Page 5: Step 2: Installing The Stationary Sections Onto The Equipment Rack
(see figure 3). See Configurations (For Reference Only) appropriate mounting hardware. Quantum 1U Rackmount Rail Installation Guide Document 81-81209-05 A01 January 2006 on page 7 Typical Rack and Slide on page 11 for information on... - Page 6 Quantum 1U Rackmount Rail Installation Guide Document 81-81209-05 A01 January 2006 Figure 4 Assembly of the Stationary Section Screws, Nuts, and Short Back Bracket Figure 5 Securing the Rail Assembly—Back View 2 Attach the short back bracket to the back end of the stationary section...
-
Page 7: For Racks Deeper Than 24 Inches
2 Attach the two long back brackets to the back pillars of the equipment rack with two screws in the upper two mounting holes (see Long back bracket Quantum 1U Rackmount Rail Installation Guide Document 81-81209-05 A01 January 2006 6). See Typical Rack and Slide on page 11 for more information. - Page 8 Quantum 1U Rackmount Rail Installation Guide Document 81-81209-05 A01 January 2006 Figure 8 Inserting the Support Bracket—Back View Figure 9 Assembly of the Slide, Bolts, Nuts, and Support Bracket 3 Insert one end of the support bracket (A) into the stationary section (B) of the rail assembly.
-
Page 9: Step 3: Installing The 1U Rackmount Into The Equipment Rack
When the release buttons on the chassis sections stop against the intermediate sections, press both release buttons (on opposite sides) and continue sliding the 1U Rackmount into the rails. See Quantum 1U Rackmount Rail Installation Guide Document 81-81209-05 A01 January 2006 figure 10). - Page 10 Quantum 1U Rackmount Rail Installation Guide Document 81-81209-05 A01 January 2006 Figure 12 Securing the 1U Rackmount into the Rack—Front View 3 Slide the 1U Rackmount completely into the rack, and secure it in place by tightening the thumbscrews on each side (see figure 12).
-
Page 11: Typical Rack And Slide Configurations (For Reference Only)
Typical Rack and Slide Configurations (For Reference Only) Figure 13 Typical Rack Configuration 1 Screws (3x) Quantum 1U Rackmount Rail Installation Guide Square hole rack Screws (2x) Rack vertical Round hole rack frame member Screws (2x) Tapped hole rack Screws (2x) - Page 12 Quantum 1U Rackmount Rail Installation Guide Document 81-81209-05 A01 January 2006 Figure 14 Typical Rack Configuration 2 KEPS nuts (2x) short back bracket Screws (2x) For racks 24 inches deep Long back bracket KEPS nuts (4x) Reinforcing plate For racks 25 to 32 inches deep...
Need help?
Do you have a question about the LTO 1U and is the answer not in the manual?
Questions and answers