Table of Contents
Advertisement
preventive safety measures reduce the risk of starting
the power tool accidentally.
■
Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
■
Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool's operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
■
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
■
Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
Keep handles and grasping surfaces dry, clean
■
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
SERVICE
■
Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
PLANER SAFETY WARNINGS
■
Wait for the cutter to stop before setting the tool
down. An exposed rotating cutter may engage the
surface, leading to possible loss of control and serious
injury.
■
Hold the power tool by insulated gripping surfaces,
because the cutter
may contact its own cord.
Cutting a "live" wire may make exposed metal parts
of the power tool "live" and could give the operator an
electric shock.
■
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the workpiece by your hand or against the body leaves
it unstable and may lead to loss of control.
■
The dust produced when using this tool may be harmful
to health. Do not inhale the dust. Use a dust absorption
system and wear a suitable dust protection mask.
Remove deposited dust thoroughly, e.g., with a vacuum
cleaner.
ADDITIONAL SAFETY RULES
■
Do not remove splinters or saw dust while tool is
running.
■
Only plane with sharp blades, avoid metals (nails,
screws). Check the workpiece before planing.
■
Do not reach into the danger area of the tool when
plugged in.
2
■
Place the front plate of the machine on to the workpiece
and switch on, before the planer blade touches the
workpiece and then guide evenly over the workpiece.
■
The v-shape notch in the front of the supporting plate
ensures safe chamfering of edges.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise and the operator
should pay special attention to avoid the following:
■
Injury caused by dust
–
Using the product will produce considerable amount
of dust and fine particles. Use the dust collection
device or connect a dust extraction vacuum when
operating the product. Wear dust masks containing
filters appropriate to the materials being worked
on. Ensure adequate workplace ventilation. Do not
eat, drink, or smoke in the work area. Only operate
on materials which are specified in the Intended
use section. Do not operate on materials (e.g.,
asbestos) which present a health hazard.
■
Injury caused by noise and vibration
–
Wear ear protection during operation. Do not
operate the product for long periods of time. See
"Risk reduction".
RISK REDUCTION
It has been reported that vibrations from handheld tools
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
numbness and blanching of the fingers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking and work practices
are all thought to contribute to the development of these
symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
■
Keep your body warm in cold weather. When operating
the unit wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud's Syndrome.
■
After each period of operation, exercise to increase
blood circulation.
■
Take frequent work breaks. Limit the amount of
exposure per day.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor about
these symptoms.
WARNING
Injuries may be caused or aggravated by prolonged use
of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
Advertisement
Table of Contents
