Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec PRDS 11-230V
Summary of Contents for Trotec PRDS 11-230V
- Page 1 PRDS 11-230V ORIGINAL INSTRUCTIONS ROTARY HAMMER...
-
Page 2: Table Of Contents
(e.g. material damage), but does not indicate hazards. Info Information marked with this symbol helps you to carry out your tasks quickly and safely. Follow the manual Information marked with this symbol indicates that the instructions must be observed. rotary hammer PRDS 11-230V... -
Page 3: Safety
• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. rotary hammer PRDS 11-230V... - Page 4 • Immediately switch off the power tool if the insertion tool blocks. The power tool can lash out to the side owing to the forces that build up consequently. rotary hammer PRDS 11-230V...
- Page 5 • for chiselling in concrete, rock and plaster flying pieces which could cause injuries. whilst adhering to the technical data. We recommend using the power tool with original Trotec accessories. Foreseeable misuse The device is not intended for drilling in natural stone.
- Page 6 Dangers can occur at the device when it is used by untrained people in an unprofessional or improper way! Observe the personnel qualifications! Warning The device is not a toy and does not belong in the hands of children. rotary hammer PRDS 11-230V...
-
Page 7: Information About The Device
• 3 x SDS drill bits (8/10/12 x 150 mm) • 1 x SDS flat chisel (14 x 250 mm) • 1 x SDS pointed chisel (14 x 250 mm) • 1 x Additional handle • 1 x Dust protection cap • 1 x Lubricant container • 1 x Transport case • 1 x Manual rotary hammer PRDS 11-230V... - Page 8 Vibration information according to EN 60745 Vibration emission value for hammer drilling in concrete a 15.037 m/s Uncertainty K 1.5 m/s Vibration emission value for chiselling a 14.868 m/s Uncertainty K 1.5 m/s Wear hearing protection. Excessive noise can lead to hearing loss. rotary hammer PRDS 11-230V...
-
Page 9: Transport And Storage
• Dry and protected from frost and heat • Ambient temperature below 45 °C • Protected from dust and direct sunlight inside the transport case 3. Then release the SDS-plus system tool holder (1). 4. Check the tool for tight fit. rotary hammer PRDS 11-230V... - Page 10 1. Loosen the fastening screw (2) at the mount. 3. Retighten the additional handle (13). 2. Insert the depth stop (6). 4. Check the additional handle (13) for tight fit. If necessary, tighten the additional handle further. rotary hammer PRDS 11-230V...
- Page 11 4. Check the key-type drill chuck (7) for tight fit. Use the dust protection cap (14) to protect yourself and your tool from falling dust particles during overhead drilling work. 1. Insert the drill bit through the dust protection cap (14) into the SDS-plus system tool holder (1). rotary hammer PRDS 11-230V...
-
Page 12: Operation
ð The operating light (16) will be illuminated as soon as Impact drilling in masonry / bricks: the power cable is plugged in. • Use a drill bit suitable for masonry / bricks. Chiselling in general: • Use a suitable chisel. rotary hammer PRDS 11-230V... - Page 13 2. Set the switch for the impact mechanism (12) to the desired position. 7. Let go of the on/off switch (4) to stop the device. 8. Wait until the device has stopped before putting it away. rotary hammer PRDS 11-230V...
- Page 14 1. Stop the tool by letting go of the on/off switch (4). 2. Turn the function selector switch (3) to the position. 3. Turn the tool manually into the desired position. 360° 4. Turn the function selector switch (3) back to the position to continue working. rotary hammer PRDS 11-230V...
-
Page 15: Available Accessories
• The setting for drilling or impact drilling should be selected. • Check whether the correct drill bit is selected. • Check whether the function selector switch (3) is set to position . This position is only suitable for chiselling. rotary hammer PRDS 11-230V... -
Page 16: Maintenance
The device becomes hot: opened must only be carried out by authorised • Check whether the tool is suitable for the tasks to be specialist companies or by Trotec. carried out. Notes on maintenance • Keep the venting slots clear to prevent the motor from •... -
Page 17: Disposal
The icon with the crossed-out waste bin on waste electrical or electronic equipment stipulates that this equipment We – Trotec GmbH – declare in sole responsibility that the must not be disposed of with the household waste at the end of product designated below was developed, constructed and its life. - Page 18 Trotec GmbH Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...