Note This signal word indicates important information (e.g. material damage), but does not indicate hazards. Info Information marked with this symbol helps you to carry out your tasks quickly and safely. cordless rotary hammer PRDS 20-20V...
Any power tool that cannot be controlled with protected supply. Use of an RCD reduces the risk of the switch is dangerous and must be repaired. electric shock. cordless rotary hammer PRDS 20-20V...
Page 4
Liquid ejected from the • Vibrations can be harmful to the human hand-arm battery may cause irritation or burns. system. Keep the vibration exposure time to a minimum. cordless rotary hammer PRDS 20-20V...
Page 5
If the device is switched on with a jammed insertion tool, the resulting forces can We recommend using the power tool with original Trotec be extreme causing the device to kick out sideways. accessories.
Page 6
Note tool. Do not touch the insertion tool bare-handed! If you store or transport the device improperly, the Wear protective gloves! device may be damaged. Note the information regarding transport and storage of the device. cordless rotary hammer PRDS 20-20V...
Red battery LED (battery charging) Device depiction Battery Depth stop SDS drill bit Battery level indication Release button Green battery LED (quick charger ready for operation) Additional handle Battery holder LED work lamp Dust protection cap cordless rotary hammer PRDS 20-20V...
Page 8
Charging current 3.5 A 3.15 A (slow-blowing) Fusing Charging time 1.5 h Cable length 1.5 m Protection class II / Sound values according to EN 60745 Sound pressure level L 82 dB(A) Sound power level L 93 dB(A) Uncertainty K 3 dB(A) cordless rotary hammer PRDS 20-20V...
• Check the contents of the transport case for completeness and look for damages. Warning Risk of suffocation! Do not leave the packaging lying around. Children may use it as a dangerous toy. • Dispose of the packaging material according to the national regulations. cordless rotary hammer PRDS 20-20V...
Page 10
Allow the battery (8) to cool down to room temperature. 5. Take the battery (8) out of the quick charger (6) by pressing and holding the release button (12) and pulling the battery (8) off the quick charger (6). cordless rotary hammer PRDS 20-20V...
Page 11
Orange – Red medium charge / power weak charge – Recharge the battery. 1. Press on the battery icon (18) on the battery (8). ð You can read the battery status from the battery level indication (11). cordless rotary hammer PRDS 20-20V...
Page 12
1. Loosen the screw connection of the additional handle (14) by rotating the gripping surface to the left. 2. Insert the depth stop (9). When doing so, make sure that the notches of the depth stop point to the device. cordless rotary hammer PRDS 20-20V...
Hammer drilling in masonry / bricks: • Use a drill bit suitable for masonry / bricks. Screwing: • When using screwdriver bits, always use a universal bit holder. Only use screwdriver bits that are suitable for the screw head. cordless rotary hammer PRDS 20-20V...
Page 14
The function selector switch (2) is used to select drilling or hammer drilling. Note Only actuate the function selector switch when the device is at a standstill! Otherwise the device might be damaged. 1. Set the function selector switch (2) to the desired position. cordless rotary hammer PRDS 20-20V...
Page 15
A wrong rotational direction may damage the tool and / or workpiece. 3. If required, set the switch for clockwise / counter- clockwise rotation (3) to centre position (lock) to block the on/off switch (4). cordless rotary hammer PRDS 20-20V...
• Check the power cable and mains plug for damage. Trotec for repair. • Check the on-site fusing. • Check the quick charger for damage. If the quick charger is damaged, stop using it. Contact the Trotec customer service. cordless rotary hammer PRDS 20-20V...
• Remove any drilling dust and, if applicable, wood chips from the SDS tool holder. • Keep the connecting terminals on the device and charger clean. • Slightly grease the tool holder with machine lubricant before inserting another tool. cordless rotary hammer PRDS 20-20V...
Declaration of conformity in accordance with the EC Machinery Directive 2006/42/EC, Annex II, Part 1, Section A Herewith, we – Trotec GmbH– declare that the machinery designated below was developed, constructed and produced in compliance with the requirements of the EC Machinery Directive in the version 2006/42/EC.