Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec PRDS 10-230V
Summary of Contents for Trotec PRDS 10-230V
- Page 1 PRDS 10-230V ORIGINAL INSTRUCTIONS ROTARY HAMMER...
-
Page 2: Table Of Contents
Info Information marked with this symbol helps you to carry out your tasks quickly and safely. Follow the manual Information marked with this symbol indicates that the operating manual must be observed. Operating manual – rotary hammer PRDS 10-230V... -
Page 3: Safety
Use of a cord safety principles. A careless action can cause severe suitable for outdoor use reduces the risk of electric shock. injury within a fraction of a second. Operating manual – rotary hammer PRDS 10-230V... - Page 4 • Wait until the power tool has come to a standstill, before putting it down. • Use the additional handle pre-assembled at the device. Losing control of the power tool may result in personal injury. Operating manual – rotary hammer PRDS 10-230V...
- Page 5 Before any work on the device, remove the mains plug from the mains socket! whilst adhering to the technical data. Hold onto the mains plug while pulling the power cable We recommend using the power tool with original Trotec out of the mains socket. accessories. Warning of electrical voltage...
-
Page 6: Information About The Device
• 3 x SDS drill bits (8/10/12 x 250 mm) • 1 x SDS flat chisel (14 x 250 mm) • 1 x SDS pointed chisel (14 x 250 mm) • 1 x Additional handle • 1 x Transport case • 1 x Manual Operating manual – rotary hammer PRDS 10-230V... - Page 7 14.8 m/s hammer drilling in concrete (ah=in) Uncertainty K 1.5 m/s Vibration emission value for 15.5 m/s chiselling (ah=in) Uncertainty K 1.5 m/s Wear hearing protection. Excessive noise can lead to hearing loss. Operating manual – rotary hammer PRDS 10-230V...
-
Page 8: Transport And Storage
• dry and protected from frost and heat • ambient temperature below 40 °C • protected from dust and direct sunlight inside the transport case 3. Then release the SDS-plus system tool holder (1). 4. Check the tool for tight fit. Operating manual – rotary hammer PRDS 10-230V... - Page 9 1. Turn the setting wheel (5) to the desired speed level. 2. Turn the additional handle (13) into the desired position. 3. Retighten the additional handle (13). 4. Check the additional handle (13) for tight fit. If necessary, tighten the additional handle further. Operating manual – rotary hammer PRDS 10-230V...
- Page 10 5. Open the key-type drill chuck (7) by means of the drill chuck key (8). 6. Insert the tool in the key-type drill chuck (7). 7. Tighten the key-type drill chuck (7) by means of the drill chuck key (8). Operating manual – rotary hammer PRDS 10-230V...
-
Page 11: Operation
Forstner bit. Impact drilling in masonry / bricks: • Use a drill bit suitable for masonry / bricks. Chiselling in general: • Use a suitable chisel. Operating manual – rotary hammer PRDS 10-230V... - Page 12 The function selector switch comes with a safety lock that has to be pushed in first, before you can change the switch position. ð Operating mode: Hammer drilling 2. Set the switch for the impact mechanism (12) to the desired position. Operating manual – rotary hammer PRDS 10-230V...
-
Page 13: Available Accessories
• Store the device according to the Storage chapter. mode. For technical reasons there will be no rotation or stroke motion. Use the two switches (3 and 12) to set the desired operating mode. Operating manual – rotary hammer PRDS 10-230V... -
Page 14: Maintenance
Please contact the customer service. If necessary, bring the • Slightly grease the tool holder with machine lubricant device to an authorized specialist electrical company or to before inserting another tool. Trotec for repair. Operating manual – rotary hammer PRDS 10-230V... -
Page 15: Disposal
Annex II, part 1, Section A addresses can be obtained from your municipality or local Herewith, we – Trotec GmbH & Co. KG – declare that the administration. For further return options provided by us please machinery designated below was developed, constructed and refer to our website www.trotec24.com. - Page 17 Trotec GmbH & Co. KG Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...