Related Manuals for Haier HDV50E1
Summary of Contents for Haier HDV50E1
- Page 1 INSTALLATION INSTRUCTIONS USER GUIDE Vented clothes dryer Model: HDV70E1 and HDV50E1...
-
Page 3: Table Of Contents
CONTENTS SAFETY AND WARNINGS INSTALLATION INSTRUCTIONS CONTROL PANEL DRYING CYCLES USING YOUR DRYER CLEANING YOUR DRYER BEFORE YOU CALL FOR SERVICE TROUBLESHOOTING IMPORTANT! SAVE THESE INSTRUCTIONS Please read these instructions carefully before using your tumble dryer. The instructions contain important information which will help you get the best out of the device and ensure safe and proper installation, use and maintenance. -
Page 4: Safety And Warnings
SAFETY AND WARNINGS Meaning of symbols on the dryer Warning: Risk of fire/Flammable materials Read the instructions ! WARNING! Fire Hazard ■ Only dry fabrics that have been washed with water. ■ Do not use heat to dry articles containing foam rubber or similarly textured rubber–like materials, dry on ‘Airing’. - Page 5 ■ At regular intervals have the interior of the dryer cleaned of any accumulated lint. This must be done by a Haier trained and supported service technician. This must be done when the dryer installation is changed from free standing or inverted, or vice versa.
- Page 6 These materials can, when heated, produce fire by spontaneous combustion. ■ The maximum mass of dry textiles depends on your model, The HDV70E1 model is rated at 7kg. The HDV50E1 model is rated at 5kg. Do not overload your dryer.
-
Page 7: Installation Instructions
■ Please help protect the environment and dispose of the packaging from around the dryer in an environmentally friendly manner. Accessories Please check your dryer model and the following accessories inside the drum: HDV50E1 HDV70E1 ■ 1 x Installation instructions ■ 1 x Installation instructions... - Page 8 INSTALLATION INSTRUCTIONS Venting Correct installation is very important for all dryers to ensure maximum efficiency and safety. IMPORTANT! Never run the dryer unless the airflow system is free from obstruction. There must be adequate ventilation to avoid the back flow of gases into the room from appliances burning fuels, including open fires, when operating the dryer.
- Page 9 INSTALLATION INSTRUCTIONS Free standing The dryer stands on the floor and can easily be moved into position. 1 Move the dryer into the desired position. Do not lift the dryer by the top panel. 2 Have a minimum clearance on all sides of at least 20mm.
- Page 10 INSTALLATION INSTRUCTIONS Mounting dryer on wall 1 Determine the position of the dryer on the wall and mark the bracket position. A minimum of 50mm is needed between the top of the dryer and the ceiling for ease of installation. If mounting above a washing machine, allow sufficient room to open the lid of the washer.
- Page 11 INSTALLATION INSTRUCTIONS Stacking installation Your dryer has been designed to be able to be stacked on the top of a Haier front load washing machine, ensure the washing machine is the same width as your dryer. Stacking bracket includes: Tools and parts required: ■...
- Page 12 INSTALLATION INSTRUCTIONS Before a rear venting option is installed the dryer must be changed from the front venting factory setup. Remove the outlet grille from the front left-hand side and replace with the outlet cover from the rear left-hand side. These covers should be gently pried at the sides to prevent damage.
- Page 13 ■ Do not touch or operate the dryer with wet hands or with bare feet. ■ A damaged power cord must be replaced by a Haier trained and supported service technician. The appliance must not be operated until it is repaired, as there is risk of electric shock.
-
Page 14: Control Panel
CONTROL PANEL Press ‘Power’ button to activate your dryer. Press it again to switch the dryer off. ‘Key Lock’ can be used to lock the buttons on your dryer.This will avoid accidental button presses. There are two drying settings with your dryer, Sensor Dry and Time Dry. The default cycle is “Normal –... -
Page 15: Drying Cycles
‘Extra’, ‘High’ dry temperature is the recommended cycle of HDV70E1 model for everyday cotton items. ‘Normal’, ‘High’ dry temperature is the recommended cycle of HDV50E1 model for everyday cotton items. Time dry It is suitable for some fabrics that you wish to dry for a specific time period. You can select 30, 60, 90, 120, 150 and 180 minute drying times. -
Page 16: Using Your Dryer
USING YOUR DRYER IMPORTANT! ■ Check the lint filter is clean before every load. Ensure it is replaced correctly before using your dryer. ■ The lint filter indicator light will flash at the beginning of every cycle when the machine is switched on, as a reminder to check the lint filter. - Page 17 USING YOUR DRYER Switch on the power supply Press the ‘Power’ button to power on your dryer. Selecting program Select your desired drying cycle by turning the control dial. As you rotate the dial, the drying cycle selected will illuminate, along with the default settings for that cycle on the right side of the control panel.
-
Page 18: Cleaning Your Dryer
CLEANING YOUR DRYER IMPORTANT! ■ If you wish to stop the dryer before the cycle has finished you MUST remove the clothes IMMEDIATELY and spread them out to cool. DO NOT leave the clothes in the dryer or bunched up in a clothes basket. Take extreme care as the drum and the load items may be extremely hot. -
Page 19: Before You Call For Service
Record the fault code and call your Haier trained and supported service technician to arrange service. If a fault code is being displayed, you can still turn your dryer off by pressing ‘Power’... -
Page 20: Troubleshooting
TROUBLESHOOTING The following is a list of problems you may encounter when using this appliance and some suggestions that may help to correct the problem. If you still have problems, please contact your Haier Repairer. PROBLEM POSSIBLE CAUSES WHAT TO DO Pressing ‘Power’... - Page 21 TROUBLESHOOTING PROBLEM POSSIBLE CAUSES WHAT TO DO Fault code warning Dryer has a fault. Refer to page 17. Noises. Dryer is overloaded. Remove some items from the dryer. Dryer has a fault. Continuous beeping or a musical series of beeps with a message displayed on digital display.
- Page 22 TROUBLESHOOTING PROBLEM POSSIBLE CAUSES WHAT TO DO Linting. Lint filter not cleaned or replaced. Ensure the lint filter is cleaned after every cycle and replaced correctly. Refer to pages 16 and 17. Loads not sorted correctly. Dry lint givers separately from lint receivers. Dry similar colours together eg light coloured items with light coloured items, dark items with dark items.
- Page 24 0180500946 2018.10.A...