For more information on features and programming, refer to the NI High-Speed Digitizers Help. For device specifications, refer to the specifications document included with your device. Both documents are available at Start»All Programs»National Instruments»NI-SCOPE» Documentation. For the most current versions of documentation, visit .
NI 5132/5133 Front Panels ......................20 NI 5152/5153/5154 Front Panels....................21 NI 5185/5186 Front Panels ......................22 NI 5622 Front Panels ........................23 Appendix B: Front Panels for Traditional NI-DAQ (Legacy) Devices..........24 NI 5102 Front Panels ........................24 NI 5112 Front Panels ........................27 NI 5620/5621 Front Panels ......................
Note SMC-based devices are based on the National Instruments Synchronization and Memory Core architecture. For more information, refer to the NI High-Speed Digitizers Help. Other Required Items In addition to the items contained in the kit, you need the following items: ❑...
PXI Chassis Screws Ejector Handle in Downward Position NI PXI Module Figure 1. PXI Module Installation PXI Express Chassis Screws Chassis Slot Markings Ejector Handle NI PXI Express Module Figure 2. PXI Express Module Installation NI PXIe-5185/5186 Modules Follow the installation instructions in the PXI/PXI Express Modules section to install the NI PXIe-5185/5186 module in PXI Express slots of the chassis.
NI PXIe-5185/5186 Startup Behavior The first time you install the NI 5185/5186 in the chassis, the NI-SCOPE driver launches a device recognition wizard. After the wizard completes, the NI 5185/5186 module goes through an initialization procedure that lasts approximately 5–10 minutes. You must wait until the initialization procedure completes before using the module.
Groove Method USB Cable Zip Tie Method Zip Tie USB Cable Strain Relief Groove (Large) Zip Tie Bar USB Cable Strain Relief Groove (Small) Figure 7. USB Cable Strain Relief Options Mounting the USB-5132/5133 You can use the NI USB-5132/5133 on a desktop or mount it to a standard DIN rail or a panel. Desktop Use The NI USB-5132/5133 has plastic guides on the underside that allow it to be stacked on top of other NI USB-5132/5133 devices.
Panel Mounting To mount the USB-513x to a board or panel, complete the following steps while referring to Figure 9. Figure 9. Mounting the USB-513x on a Panel Note Do not apply the rubber feet to the USB-513x when panel mounting the device. Note Apply strain relief, as described in the USB Cable Strain Relief...
Soft Front Panel. The NI-SCOPE SFP provides context-sensitive help for its controls. Acquiring Data Programmatically You can use NI-SCOPE to begin programming the digitizer in your ADE. Refer to the Programming section of the NI High-Speed Digitizers Help at Start»All Programs»National Instruments» NI-SCOPE»Documentation. NI-SCOPE Examples ™...
To begin making measurements with an NI high-speed digitizer, complete the following steps: Launch your ADE. Navigate to Start»All Programs»National Instruments»NI-SCOPE»Examples and open one of the examples. If you are not sure which example to run, begin with the Getting Started example.
Appendix A: Front Panels for SMC-Based Devices and USB Devices This appendix describes digitizer front panels and signal connections for SMC-based devices and USB devices: NI 5105, NI 5114, NI 5122, NI 5124, NI 5132, NI 5133, NI 5142, NI 5152, NI 5153, NI 5154, NI 5185, NI 5186, NI 5622, and NI 5922.
NI 5122/5124/5142/5922 Front Panels Figure 13 shows the NI PXI-5122/5124/5142/5922 and NI PCI-5122/5124/5142/5922 front panels. The NI PXI-5122 and the NI PXIe-5122 front panels are identical. Figure 13. NI 5122/5124/5142/5922 Front Panels Table 3 describes the signal connections for the NI 5122/5124/5142/5922. Table 3.
NI 5132/5133 Front Panels Figure 15 shows the NI USB-5132 and NI USB-5133 front panels. CH 0 CH 1 PFI 1 NI USB-5132 8-bit, 50 MS/s Digitizer CH 0 CH 1 PFI 1 NI USB-5133 8-bit, 100 MS/s Digitizer Figure 15. NI 5132/5133 Front Panels Figure 16 shows the NI 5132/5133 back panel.
Appendix B: Front Panels for Traditional NI-DAQ (Legacy) Devices This appendix describes digitizer front panels and signal connections for the following Traditional NI-DAQ (Legacy) devices: NI 5102, NI 5112, and NI 5620/5621. NI 5102 Front Panels The NI 5102 is available for PXI and PCI platforms. This section describes the front panels and signal connections for both types of NI 5102 digitizers.
Page 27
(NI PCI-5102) Figure 22 shows the NI PCI-5102 front panel. CH 0 CH 1 TRIG PFI 1 PFI 2 Figure 22. NI PCI-5102 Front Panel Table 9 describes the signal connections for the NI PCI-5102. Table 9. NI PCI-5102 Front Panel Signal Connections Connector Description Function...
NI 5620/5621 Front Panels Figure 24 shows the NI PXI-5620/5621 front panels. NI PXI-5620 NI PXI-5621 64 MS/s Digitizer 64 MS/s Digitizer INPUT INPUT +20 dBm MAX +20 dBm MAX ±2 VDC MAX ±3 VDC MAX REF CLK IN REF CLK IN +16 dBm MAX +20 dBm MAX ±10 VDC MAX...
Appendix D: Troubleshooting Front Panel ACCESS LED on PXI/PXI Express Module is Off when PXI/PXI Express Chassis is On If the ACCESS LED on the digitizer is not lit after you power on the PXI/PXIe chassis, a problem may exist with the PXI/PXIe power rails, a hardware device, or the LED. Note The LEDs may not light until the device has been configured in MAX.
If the software optimization application is not installed on your system, use the MXI software CD or the National Instruments Driver CD included with your kit to install the software. After installation, you may need to restart your computer before running the MXI Optimization Application.
Thailand 662 278 6777, Turkey 90 212 279 3031, United Kingdom 44 (0) 1635 523545 CVI, LabVIEW, National Instruments, NI, ni.com, the National Instruments corporate logo, and the Eagle logo are trademarks of National Instruments Corporation. Refer to the Trademark Information at ni.com/trademarks for other National Instruments trademarks. Tektronix, Enabling Technology is a trademark of Tektronix, Inc.
Page 34
、 、 、 、 、 NI 5621 NI 5622 NI 5900 NI 5922 、 、 、および に適用します。 機能の詳細やプログラミング方法については、 『 高速デジタイザヘルプ』を参照してくだ さい。 デバイス仕様の詳細については、デバイスに付属する仕様書を参照してください。 両 National Instruments NI-SCOPE ドキュメントはスタート→すべてのプログラム→ → → ドキュメントから入手できます。 NI-SCOPE 最新のドキュメントは、 で入手できます。 の最新バージョン ni.com/manuals は、 で入手できます。 ni.com/idnet 目次 ................................2 表記規則...
A: SMC 付録 対応デバイスおよび デバイスのフロントパネル NI 5105 NI 5114 NI 5122 この付録では、 対応デバイスおよび デバイス 、 、 、 NI 5124 NI 5132 NI 5133 NI 5142 NI 5152 NI 5153 NI 5154 NI 5185 NI 5186 、 、 、 、 、 、...
NI 5620/5621 フロントパネル NI PXI-5620/5621 図 は、 のフロントパネルを示します。 NI PXI-5620 NI PXI-5621 64 MS/s Digitizer 64 MS/s Digitizer INPUT INPUT +20 dBm MAX +20 dBm MAX ±2 VDC MAX ±3 VDC MAX REF CLK IN REF CLK IN +16 dBm MAX +20 dBm MAX ±10 VDC MAX ±10 VDC MAX...