Subscribe to Our Youtube Channel
Related Manuals for Fisher & Paykel DD60DA9
Summary of Contents for Fisher & Paykel DD60DA9
- Page 1 DOUBLE DISHDRAWER™ DISHWASHER CONTEMPORARY DD60DA9, DD60DC9, DD60DDF9, DD60DN9 & DD60DZ9 INSTALLATION GUIDE NZ AU UK IE...
-
Page 3: Safety And Warnings
SAFETY AND WARNINGS WARNING! WARNING! Electric Shock Hazard Tip Hazard Failure to follow this advice may result in Failure to follow this advice may result in electrical shock or death. injury or product damage. • Before installing the DishDrawer, remove the •... -
Page 4: Tools And Components
TOOLS AND COMPONENTS PARTS SUPPLIED TOOLS REQUIRED Keep all packing materials until the unit has been inspected. Not supplied Inspect the product to ensure there is no shipping damage. If any damage is detected contact the dealer or retailer you bought the product from to report the damage. Fisher &... -
Page 5: Product Dimensions
PRODUCT DIMENSIONS – DD60DC MODELS DD60DC PRODUCT DIMENSIONS A Overall height* 820 – 880 B Overall width C Overall depth D Height of chassis E Depth of chassis F Height of upper door panel G Height of lower door panel PLAN ISOMETRIC H Depth of door panel I Ventilation gap between door panels J Depth of toe kick recess**... - Page 6 PRODUCT DIMENSIONS – DD60DA MODELS DD60DA PRODUCT DIMENSIONS A Overall height* 820 – 880 B Overall width C Overall depth D Height of chassis E Depth of chassis F Height of upper door panel G Height of lower door panel PLAN ISOMETRIC H Depth of door panel I Ventilation gap between door panels J Height from base of door to floor*...
- Page 7 PRODUCT DIMENSIONS – DD60DD MODELS DD60DD PRODUCT DIMENSIONS A Overall height* 820 – 880 B Overall width C Overall depth D Height of chassis E Depth of chassis F Height of upper door panel G Height of lower door panel H Depth of door panel PLAN ISOMETRIC I Ventilation gap between door panels...
- Page 8 PRODUCT DIMENSIONS – DD60DN MODELS DD60DN PRODUCT DIMENSIONS A Overall height* 820 - 880 B Overall width C Overall depth D Height of chassis E Depth of chassis F Depth of door panel G Height of upper door panel H Height of lower door panel PLAN ISOMETRIC I Ventilation gap between door panels...
-
Page 9: Cabinetry Dimensions
CABINETRY DIMENSIONS CLEARANCES Connections can be located in an adjacent cabinet on either side of the DishDrawer*** PLAN ISOMETRIC CABINETRY DIMENSIONS CABINETRY CLEARANCES A Minimum inside height* A Minimum clearance to adjacent cupboard door B Inside width 600 – 610 B Minimum clearance to corner cupboard C Minimum inside depth** D Recommended height of adjacent cabinetry E Height of toe kick area***... -
Page 10: Left Side
PLUMBING & ELECTRICAL CONSIDERATIONS Hose and cord lengths Your services can be installed to either the left-hand or right-hand side of the product in an adjacent cabinet. Refer to ‘Cabinetry preparation’ for service access requirements. If the drain hoses supplied are not long enough to reach your services, you may purchase a Fisher &... - Page 11 CABINETRY PREPARATION SERVICE ACCESS MOISTURE PROTECTION We recommend locating the service holes on either side of the DishDrawer as shown below. If the holes are created through wood, ensure the edges are smooth and rounded If the holes are created through metal, ensure an edge protector is fitted. Align the supplied moisture protection tape to the cabinetry as illustrated Ensure this area is free of debris before carefully...
- Page 12 SECURE TO CABINETRY VIA BRACKETS (METHOD A) Secure all four side brackets to the DishDrawer™ Dishwasher, aligning Partially open one of the drawers and bracket A with slot A and bracket B remove the first screw cover from the with slot B. trim moulding.
- Page 13 SECURE TO CABINETRY VIA DRAWER REMOVAL (METHOD B) Using your hand or a screwdriver, level the DishDrawer™ Dishwasher as required. Rotate clockwise to increase Optionally, fit the two top brackets. the height of each leg and anticlockwise Ensure the ends of the brackets are not to lower.
- Page 14 INSTALL TOE KICK – DD60DC, DD60DD & DD60DN MODELS Measure toe kick height. Where Snap excess + smooth edges. the toe kick meets the bottom of the tub is the recommended Snap both end tabs. cut-off point. Slide toe kick onto the mounting rails and secure Carefully score toe kick at desired height...
- Page 15 INSTALL TOE KICK – DD60DA MODELS Measure the distance from the floor to the base of the lower door panel. Refer to the table below for the recommended Punch or drill out the two mounting cut location. holes with a 5mm drill bit on each side of the toe kick as shown.
- Page 16 PLUMBING & ELECTRICAL CONNECTION Ø38MM STANDPIPE INSTALLATION SINK TRAP/WASTE TEE INSTALLATION Install the drain hose support to the Install the drain hose support to the back wall, as close to the underside of back wall, as close to the underside of the countertop as possible.
-
Page 17: Installer Checklist
INSTALLER CHECKLIST TO BE COMPLETED BY THE INSTALLER Electrical … Ensure all electrical tests have been conducted in accordance with local regulations. Installation … Check all parts are installed correctly and are secure. Test operation … Ensure all clearance gaps have been maintained. …... -
Page 18: Troubleshooting
TROUBLESHOOTING DD60DA and DD60DC models No program indicator lights up when the drawer is opened Ensure power is connected and is switched on. DISPLAY POSSIBLE CAUSE WHAT TO DO may need to be activated. Refer to your user guide for details. AUTO POWER-ON Water 1 Ensure the water supply is turned on. - Page 21 FISHERPAYKEL.COM © Fisher & Paykel Appliances 2023. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue.
Need help?
Do you have a question about the DD60DA9 and is the answer not in the manual?
Questions and answers