Nedis TVRC2180BK - Universal Remote Control Manual

Table of Contents

Contents

1 Overview of the device
2 Programming remote control to the device
3 Automatic search
4 Safety
5 Documents / Resources
- 5.1 References
- 5.2 Download manual

Overview of the device

1.On/off button	Switch on or off the device	2.Mute button LED indicator	Mute or unmute the sound
3. Digit buttons	Select stored stations	4. Back button	Go back
5. Favourite button	Favourites	6. Volume +/- buttons	Increase or decrease the volume
7. Channel +/- buttons	Next or previous channel	8. Menu button	Display the menu
9. Exit button	Exit	10. List button	List function
11. AV button	Audio/Video	12. PIP button	Picture-in-picture (PiP)
13. Zoom button	Zoom function	14. Arrow buttons	Navigation
15. OK button	Confirm	16. Teletext button	Teletext
17. Display button	Display function	18. TV button	TV function
19. Sleep button	Sleep mode	20. Colour buttons	Individual button configurations
21. Record button	Record	22. Play button	Start playback
23. Pause button	Pause playback	24. Stop button	Stop playback
25. Fast-forward button	Fast-forward playback	26. Rewind button	Rewind playback
27. Next button	Next channel or menu item	28. Previous button	Previous channel or menu item
29. TV button	TV media selection	30. VCR button	VCR media selection
31. SAT button	Satellite media selection	32. DVD button	DVD media selection
33. DVB-T button	DVB-T media selection	34. Battery compartment	Insert the batteries (2x AAA) into the battery compartment.

Programming remote control to the device

Switch on the device to be programmed.
Find the correct brand of the device in the code list. Make a note of the first code in the code list.
Press and hold the required device button (TV/VCR/SAT/DVD/DVB-T) until the LED indicator comes on.
Enter the previously identified code.

Note:
If the LED indicator goes off, the code has been accepted. If the device is switched on or off, the code is correct. If the device is not switched on or off, repeat the previous steps using another code.

Automatic search

Switch on the device to be programmed.
Press and hold the required device button (TV/VCR/SAT/DVD/DVB-T) until the LED indicator comes on.
Point the remote control to the device. Press and slowly release the on/off button. Note: If the device is switched off, the code has been found.
Immediately press the required device button (TV/VCR/SAT/DVD/DVB-T) to confirm the code.

Note:
For buttons that do not operate correctly, repeat the previous steps until the correct code is found.

Safety

General safety

Read the manual carefully before use. Keep the manual for future reference.
The manufacturer is not liable for consequential damages or for damages to property or persons caused by nonobservance of the safety instructions and improper use of the device.
Only use the device for its intended purposes. Do not use the device for other purposes than described in the manual.
Do not use the device if any part is damaged or defective. If the device is damaged or defective, replace the device immediately.

Battery safety

Use only the batteries mentioned in the manual.
Do not use old and new batteries together.
Do not use batteries of different types or brands.
Do not install batteries in reverse polarity.
Do not short-circuit or disassemble the batteries.
Do not expose the batteries to water.
Do not expose the batteries to fire or excessive heat.
Batteries are prone to leakage when fully discharged. To avoid damage to the product, remove the batteries when leaving the product unattended for longer periods of time.
If liquid from the batteries comes into contact with skin or clothing, immediately rinse with fresh water.

Cleaning and maintenance

Do not use cleaning solvents or abrasives.
Do not clean the inside of the device.
Do not attempt to repair the device. If the device does not operate correctly, replace it with a new device.
Do not immerse the device in water or other liquids.
Clean the outside of the device using a soft, damp cloth. Thoroughly dry the device with a clean, dry cloth.