Table of Contents
Advertisement
Quick Links
SINUMERIK
SINUMERIK ONE
ONE MCP Part 2: MCP 2400.c
Equipment Manual
Valid for:
Control system
SINUMERIK ONE
SINUMERIK 840D sl/840DE sl
07/2020
A5E50324716B AA
Fundamental safety
instructions
Overview
Dimension drawings
Operator control and
display elements
Technical data
Using the slide-in labels
1
2
3
4
5
6
Advertisement
Table of Contents
Related Manuals for Siemens SINUMERIK ONE MCP 2400.c
Summary of Contents for Siemens SINUMERIK ONE MCP 2400.c
- Page 1 Fundamental safety instructions Overview Dimension drawings SINUMERIK Operator control and display elements SINUMERIK ONE ONE MCP Part 2: MCP 2400.c Technical data Using the slide-in labels Equipment Manual Valid for: Control system SINUMERIK ONE SINUMERIK 840D sl/840DE sl 07/2020 A5E50324716B AA...
- Page 2 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
-
Page 3: Table Of Contents
Table of contents Fundamental safety instructions......................5 General safety instructions....................5 Equipment damage due to electric fields or electrostatic discharge ........8 Warranty and liability for application examples ..............9 Security information ......................9 Residual risks of power drive systems ................. 10 Overview.............................. - Page 4 Table of contents ONE MCP Part 2: MCP 2400.c Equipment Manual, 07/2020, A5E50324716B AA...
-
Page 5: Fundamental Safety Instructions
Fundamental safety instructions General safety instructions WARNING Electric shock and danger to life due to other energy sources Touching live components can result in death or severe injury. • Only work on electrical devices when you are qualified for this job. •... - Page 6 Fundamental safety instructions 1.1 General safety instructions WARNING Electric shock due to equipment damage Improper handling may cause damage to equipment. For damaged devices, hazardous voltages can be present at the enclosure or at exposed components; if touched, this can result in death or severe injury.
- Page 7 • Therefore, if you move closer than 20 cm to the components, be sure to switch off radio devices or mobile telephones. • Use the "SIEMENS Industry Online Support app" only on equipment that has already been switched off. WARNING...
-
Page 8: Equipment Damage Due To Electric Fields Or Electrostatic Discharge
Fundamental safety instructions 1.2 Equipment damage due to electric fields or electrostatic discharge WARNING Unexpected movement of machines caused by inactive safety functions Inactive or non-adapted safety functions can trigger unexpected machine movements that may result in serious injury or death. •... -
Page 9: Warranty And Liability For Application Examples
Siemens’ products and solutions undergo continuous development to make them more secure. Siemens strongly recommends that product updates are applied as soon as they are available and that the latest product versions are used. Use of product versions that are no longer supported, and failure to apply the latest updates may increase customer’s exposure to cyber... -
Page 10: Residual Risks Of Power Drive Systems
Fundamental safety instructions 1.5 Residual risks of power drive systems Industrial Security Configuration Manual (https://support.industry.siemens.com/cs/ww/en/ view/108862708) WARNING Unsafe operating states resulting from software manipulation Software manipulations, e.g. viruses, Trojans, or worms, can cause unsafe operating states in your system that may lead to death, serious injury, and property damage. - Page 11 Fundamental safety instructions 1.5 Residual risks of power drive systems 3. Hazardous shock voltages caused by, for example: – Component failure – Influence during electrostatic charging – Induction of voltages in moving motors – Operation and/or environmental conditions outside the specification –...
- Page 12 Fundamental safety instructions 1.5 Residual risks of power drive systems ONE MCP Part 2: MCP 2400.c Equipment Manual, 07/2020, A5E50324716B AA...
-
Page 13: Overview
Overview This manual describes the specific properties of the SINUMERIK ONE MCP 2400.c machine control panel. The documentation is always structured in 2 parts. Part 1 contains general information that applies to all machine control panels. Part 2 covers specifics of individual machine control panels. - Page 14 Overview ONE MCP Part 2: MCP 2400.c Equipment Manual, 07/2020, A5E50324716B AA...
-
Page 15: Dimension Drawings
Dimension drawings Figure 3-1 Front, rear and side view of MCP 2400.c (all specifications in mm) The installation clearance for the MCP is 75 mm. ONE MCP Part 2: MCP 2400.c Equipment Manual, 07/2020, A5E50324716B AA... - Page 16 Dimension drawings Panel cutout The MCP 2400.c is secured using 14 M5 nuts. The tightening torque is 1.5 Nm. Use spring elements in addition to the M5 nuts. In the sealing area Figure 3-2 Panel cutout of MCP 2400.c (all specifications in mm) ONE MCP Part 2: MCP 2400.c Equipment Manual, 07/2020, A5E50324716B AA...
-
Page 17: Operator Control And Display Elements
Operator control and display elements Front side Overview ① Emergency stop button ② Keypad 1 (operating mode block) ③ Keypad 2 (customer keys) ④ Keypad 3 (customer keys) ⑤ Keypad 4 (axis block) ⑥ Powerride 2 (spindle) + keypad 4.2 ⑦... -
Page 18: Rear Side
Operator control and display elements 4.2 Rear side Rear side ① Protective conductor connection ② Power supply interface X10 ③ Switch S2 ④ Ethernet interfaces X20 port 1/ port 2 ⑤ Handwheel connections X60/ X61 ⑥ Emergency stop ⑦ 2x mounting space for 22.5 mm elements ⑧... -
Page 19: Technical Data
Technical data MCP 2400.c Safety Safety class according to EN 50178 III; PELV Degree of protection according to EN Front: IP65 Keyswitch: IP54 Rear: IP00 60529 Approvals CE / UL / EAC Flame resistance UL 94 V-1 UL identifier MCPS2002-578218B-0642111AA0 Electrical data Overvoltage category Secondary circuit supplied from primary circuits up to Cat. - Page 20 Technical data MCP 2400.c Temperature change Max. 30 K/h Relative humidity 5 ... 90% (without condensation) Permissible change in the relative humidity Max. 6%/h Pollution degree 2 (only use indoors) Mechanical environmental conditions Classification of the mechanical environ‐ Class 3M2 according to EN 60721-3-3 ment Vibration load during operation Frequency range: 10 –...
- Page 21 Technical data Note Damage to components by coolants and lubricants The SINUMERIK operator components have been designed for industrial use, particularly on machine tools and production machines. This also takes into account the use of commercially available coolants and lubricants. The use of aggressive compounds and additives can damage components and result in their failure.
- Page 22 Technical data ONE MCP Part 2: MCP 2400.c Equipment Manual, 07/2020, A5E50324716B AA...
-
Page 23: Using The Slide-In Labels
Using the slide-in labels Use the following dimension drawing to create the slide-in labels, as well as for positioning the symbols and the cut edges of the slide-in label: ① Max. inscription area for font/ symbols Figure 6-1 Slide-in labels ONE MCP Part 2: MCP 2400.c Equipment Manual, 07/2020, A5E50324716B AA... - Page 24 Using the slide-in labels ONE MCP Part 2: MCP 2400.c Equipment Manual, 07/2020, A5E50324716B AA...
-
Page 25: Index
Index MCP 2400.c Emergency stop button, 21 Technical data, 19 Current consumption, 19 Power consumption, 19 ONE MCP Part 2: MCP 2400.c Equipment Manual, 07/2020, A5E50324716B AA... - Page 26 Index ONE MCP Part 2: MCP 2400.c Equipment Manual, 07/2020, A5E50324716B AA...