Related Manuals for Dahua Technology DH-IPC-PFW83242-A180-S2
Summary of Contents for Dahua Technology DH-IPC-PFW83242-A180-S2
- Page 1 HD IR Panoramic Bullet Network Camera Quick Start Guide ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. V1.0.2...
-
Page 2: Foreword
Quick Start Guide Foreword General This manual introduces the installation and operations of network camera. Read carefully before using the device, and keep the manual safe for future reference. Safety Instructions The following signal words might appear in the manual. Signal Words Meaning Indicates a high potential hazard which, if not avoided, will result in... - Page 3 Quick Start Guide We are not liable for losses incurred due to operating of the product in ways that are not in compliance with the manual. The manual will be updated according to the latest laws and regulations of related jurisdictions. ...
-
Page 4: Important Safeguards And Warnings
Quick Start Guide Important Safeguards and Warnings This section introduces content covering the proper handling of the device, hazard prevention, and prevention of property damage. Read carefully before using the device, comply with the guidelines when using it. Transportation Requirements Transport the device under allowed humidity and temperature conditions. - Page 5 Quick Start Guide An emergency disconnect device must be installed during installation and wiring at a readily accessible location for emergency power cut-off. We recommend you use the device with a lightning protection device for stronger protection against lightning. For outdoor scenarios, strictly comply with the lightning protection regulations. Ground the function earthing portion of the device to improve its reliability (certain models ...
- Page 6 Quick Start Guide Maintenance Requirements Strictly follow the instructions to disassemble the device. Non-professionals dismantling the device can result in it leaking water or producing poor quality images. For a device that is required to be disassembled before use, make sure the seal ring is flat and in the seal groove when putting the cover back on.
-
Page 7: Table Of Contents
Quick Start Guide Table of Contents Foreword ................................I Important Safeguards and Warnings ......................III 1 Introduction ..............................1 Cable ....................................... 1 Connecting Alarm Input/output ............................2 2 Network Configuration ..........................4 Initializing the Camera ................................4 Changing the Device IP Address ............................5 Logging in to Webpage ................................ -
Page 8: Introduction
Quick Start Guide Introduction Cable Waterproof all the cable joints with insulating tape and waterproof tape to avoid water damage and prevent short circuits from occurring. For details, see FAQ manual. Cables Table 1-1 Cable information No. Port Name Function Description Audio output Connects to speaker to output audio signal. -
Page 9: Connecting Alarm Input/Output
Quick Start Guide For more information about I/O port, see Table 1-2. Table 1-2 Alarm information Port Port Name Function Outputs alarm signal to alarm device. ALARM_OUT ALARM_OUT_G When connecting to alarm device, only the ALARM_OUT port and ALARM_OUT_GND port with the same number can be used together. Alarm I/O ALARM_IN1 Receives the switch signal of external alarm source. - Page 10 Quick Start Guide Alarm output Log in webpage, and then configure alarm input and alarm output in alarm setting. The alarm input in the webpage is corresponding to the alarm input end of the I/O port. There will be high level and low level alarm signal generated by the alarm input device when alarm occurs, set the input mode to "NO"...
-
Page 11: Network Configuration
Quick Start Guide Network Configuration Device initialization and IP setting can be finished with the ConfigTool or on webpage. For more information, see the Web Operation Manual. Device initialization is available on select models, and it is required at first use and after device is ... -
Page 12: Changing The Device Ip Address
Quick Start Guide Select Auto-check for updates as needed, and then click OK to initialize the device. If initialization failed, click to see more information. Click Finish. Changing the Device IP Address You can change the IP address of one or more devices at a time. This section is based on changing ... -
Page 13: Installation
Quick Start Guide Installation Packing List Tools required for installation, such as the electric drill, are not included in the package. The operation manual and information on the tools are on the disk or the QR code. Packing list Dimensions Dimensions (mm [inch]) -
Page 14: Installing The Camera
Quick Start Guide Installing the Camera 3.3.1 Installation Methods Wall-mounted Pole-mounted Corner-mounted 3.3.2 (Optional) Installing SD Card SD card slot is available on select models. Please disconnect the power from the device before installing the SD card. Press the reset button for 10 seconds to reset the device. ... -
Page 15: Attaching The Camera
Quick Start Guide Install the SD card 3.3.3 Attaching the Camera Make sure the mounting surface is strong enough to hold at least three times of the device weight. -
Page 16: Optional) Installing Waterproof Connector
Quick Start Guide Cable going through the mounting surface Cable going through the side cable tray 3.3.4 (Optional) Installing Waterproof Connector This part is only needed when a waterproof connector comes with the device and the device is used outdoors. -
Page 17: Adjusting Sunshield
Quick Start Guide Install the waterproof connector 3.3.5 Adjusting Sunshield Adjust sunshield... -
Page 18: Adjusting Angle
Quick Start Guide 3.3.6 Adjusting Angle Adjust the lens angle... - Page 19 Quick Start Guide...