Table of Contents
Advertisement
PRE-INSTALLATION CONSIDERNATIONS
1. UNPACKING
Unpack the radio from its shipping container and check
for accessory items. If any item is missing, please contact
KENWOOD immediately.
2. LICENSING REQUIREMENTS
Federal regulations require a station license for each ra-
dio installation (mobile or base) be obtained by the equip-
ment owner. The licensee is responsible for ensuring trans-
mitter power, frequency, and deviation are within the limits
permitted by the station license.
Transmitter adjustments may be performed only by a li-
censed technician holding an FCC first, second or general
class commercial radiotelephone operator's license. There
is no license required to install or operate the radio.
3. PRE-INSTALLATION CHECKOUT
3-1. Introduction
Each radio is adjusted and tested before shipment. How-
ever, it is recommended that receiver and transmitter opera-
tion be checked for proper operation before installation.
3-2. Testing
The radio should be tested complete with all cabling and
accessories as they will be connected in the final installa-
tion. Transmitter frequency, deviation, and power output
should be checked, as should receiver sensitivity, squelch
operation, and audio output. QT equipment operation
should be verified.
4. PLANNING THE INSTALLATION
4-1. General
Inspect the vehicle and determine how and where the
radio antenna and accessories will be mounted.
Plan cable runs for protection against pinching or crush-
ing wiring, and radio installation to prevent overheating.
4-2. Antenna
The favored location for an antenna is in the center of a
large, flat conductive area, usually at the roof center. The
trunk lid is preferred, bond the trunk lid and vehicle chassis
using ground straps to ensure the lid is at chassis ground.
4-3. Radio
The universal mount bracket allows the radio to be
mounted in a variety of ways. Be sure the mounting surface
is adequate to support the radio's weight. Allow sufficient
space around the radio for air cooling. Position the radio
close enough to the vehicle operator to permit easy access
to the controls when driving.
4-4. DC Power and wiring
1. This radio may be installed in negative ground electrical
systems only. Reverse polarity will cause the cable fuse
to blow. Check the vehicle ground polarity before installa-
tion to prevent wasted time and effort.
GENERAL / 概述
安装前条件
1. 开箱
从运输包装中取出本无线电设备并检查附件。 如果有任何组
件遗失，请立即与 KENWOOD 联系。
2. 所需许可证
联邦法规要求设备所有者必须使每一个安装无线电的地点
（移动站或基站）获得许可证。持有许可证者必须确保发射功
率、频率以及频偏在许可证的有限允许范围之内。
必须只能由经许可的、 持有FCC一级、 二级或高级商业无线
电话机操作者证书的技术人员进行发射调整。 安装或操作本无
线电设备无需许可。
3. 安装前检查
3-1. 说明
在运输之前每一台无线电设备均已调整和测试过。 但是， 在
安装之前最好检查接收和发射以便操作正确。
3-2. 测试
无线电设备应该按照电缆和附件最终安装时的连接进行完整
的测试。应该检查发射频率、频偏和输出功率，同样应该检查
接收灵敏度、静噪和音频输出。应该检验信令操作。
4. 安装的步骤
4-1. 概述
检查车辆并确认如何以及在何处安装无线电天线和附件。
安排好电缆的位置， 避免挤压或碾碎布线， 同时无线电设备
避免过热。
4-2. 天线
天线的最佳位置应该在一个宽阔， 平整导电区域的中心， 通
常在车顶的中心。行李箱的盖子更好，将地线黏结在行李箱的
盖子和车辆的外壳上确保行李箱盖子接地。
4-3. 无线电设备
通用安装托架允许以多种方法安装无线电设备。 确认安装的
表面足以支撑无线电设备的重量。 无线电设备的周围留出适当
的空间进行散热。 将无线电设备尽可能的安装在靠近车辆操作
者的位置上，以便在驾驶时易于控制。
4-4. 直流电源和布线
1. 本无线电设备只能被安装在负极接地电子系统中。 反向极性
将导致电缆保险丝熔断。在安装之前检查车辆的接地极性，
避免工作效率低以及浪费时间。
TK-8108
3
Advertisement
Table of Contents
