Table of Contents
Advertisement
TK-8108
■ Temporary delete
It is possible to delete channel temporary during scan.
When scan stops on unnecessary channel for example by
interference of the other party, activate the delete function
(for example press and hold the key for approximately one
second), then that channel is deleted temporarily and scan
re-start immediately.
The temporary deleted channels return to pre-set delete/
add channels, when the transceiver is turned off or the scan
function is switched off.
5. Details of Features
■ Time-out timer
The time-out timer can be programmed in 30 seconds
increments from 30 seconds to five minutes and off. If the
transmitter is transmitted continuously for longer than the
programmed time, the transmitter is disabled and a warning
tone sounds while the PTT button is held down. The warn-
ing tone stops when the PTT button is released.
■ PTT ID
PTT ID provides a DTMF ANI to be sent with every time
PTT (beginning of transmission, end of transmission, or
both).
You can program PTT ID "on" or "off" for each channel.
The contents of ID are programmed each Radio.
The timing that the transceiver sends ID is program-
mable.
BOT : DTMF ID (Beginning of TX) is sent on beginning of
transmission.
EOT : DTMF ID (End of TX) is sent on end of transmis-
sion.
Both : DTMF ID (Beginning of TX) is sent on beginning of
transmission and DTMF ID (End of TX) is sent on end of
transmission.
■ Off hook decode
If the Off hook decode function has been enabled, re-
moving and replacing the microphone on the hook has no
effect for decoding QT/DQT and option signalling.
■ "TOT" pre-alert
The transceiver has "TOT" pre-alert timer. This parameter
selects the time at which the transceiver generates "TOT"
pre-alert tone before "TOT" is expired.
"TOT" will be expired when the selected time passes
from a TOT pre-alert tone.
■ "TOT" re-key time
The transceiver has "TOT" re-key timer. This timer is the
time you can not transmit after "TOT" exceeded. After "TOT"
re-key time expired you can transmit again.
■ "TOT" reset time
The transceiver has "TOT" reset timer. This timer is the
minimum wait time allowed during a transmission that will
reset the "TOT" count.
"TOT" reset time causes the "TOT" to continue even after
PTT is released unless the "TOT" reset timer has expired.
8
OPERATING FEATURES / 操作特性
■ 临时删除
可以在扫描进行中暂时消除信道。如果扫描停在不需要的信
道 (例如对方的干扰) 上，则可启动消除键 (例如按该键并保持
约 1 秒钟)，该信道将被暂时消除并立即重新启动扫描。
当收发机关闭或扫描功能关闭时，暂时删除的信道将返回到
预设的消除/添加信道中。
5. 详细功能
■ 超时计时器
可以以 30 秒为增量设置超时计时器，可设置范围为 30 秒
到 5 分钟或关闭。当发射器连续发射时间超过了预设时间时，
发射器将被禁用并且在按住 PTT 键时鸣响警告音。放开 PTT 键
后警告音停止。
■ PTT ID码
伴随每一次PTT (发射开始，发射结束，或两者兼有)，PTT
ID码提供一个被发送的DTMF ANI。
可以将各信道 PTT ID 设为"开"或"关"。分别编制各收
发机的 ID 内容。
车载机发送ID码的时间是可编制的。
BOT∶在发射开始时发送DTMF ID码 (发射开始)。
EOT∶在发射结束时发送DTMF ID码 (发射结束)。
两者兼有∶在发射开始时发送DTMF ID码 (发射开始)。 在
发射结束时发送DTMF ID码 (发射结束)。
■ 挂断解码
如果挂断解码功能生效，则接通时消除和更换话筒对于QT/
DQT解码和可选信令无效。
■ "TOT" 预先告警
车载台具有一个"TOT"预先告警计时器。在"TOT"终止
之前，此参数设定在手持机产生"TOT"预先告警音时的时
间。
当TOT预先告警音发出开始时"TOT"将终止。
■ "TOT"再按键时间
车载台具有一个"TOT"再按键定时器。在"TOT"时间超
出之前，此定时器是用户不能发射的时间。在"TOT"再按键
时间终止后，用户可以再发射。
■ "TOT"复位时间
车载台具有一个"TOT"复位计时器。在复位"TOT"计数
的发射过程中，此计时器是最小允许等待时间。
除非"TOT"复位计时器终止，否则即使松开PTT键之后，
"TOT"复位时间也使"TOT"继续进行。
Advertisement
Table of Contents
