Watec WAT-902H3 SUPREME Operation Manual

Monochrome CCD Camera
Operation Manual
This Operation Manual covers safety, camera functions, installation and
the correct operating procedure for the WAT-902H SUPREME. First,
2/3
we ask you to read this Operation Manual thoroughly, then install and
operate the WAT-902H SUPREME as advised. In addition, for future
2/3
reference, we also advise safekeeping of this manual.
Please contact the distributor or dealer from which the WAT-
902H 2/3 SUPREME was purchased, if you do not understand the
installation, operation or safety instructions laid out in this manual. Not
understanding the contents of the Operation Manual sufficiently may
cause damage to the camera.
Guide to the Safety Symbols
The definitions of the symbols used in this operation manual are:
When you do not adhere to or take notice of the "Danger"
sign, it may lead to a serious accident such as death or
D a n g e r
injury caused by fire or electric shock.
When you do not adhere to or take notice of the "Warning"
W a r n i n g
sign, it may cause severe damage such as a physical injury.
When you do not adhere to or take notice of the "Caution"
sign, it may incur injury and cause damage to peripheral
C a u t i o n
objects in the immediate surroundings.
Cautions for Safety
WAT-902H SUPREME is designed to be used safely; however, if not
2/3
used safely, it may lead to a physical accident caused by fire and
electric shock. Therefore, please keep and read the "Cautions for
Safety" below for protection against accidents.
•
Do not disassemble and/or modify the WAT-902H
D a n g e r
SUPREME.
•
Do not operate the WAT-902H 2/3 SUPREME with wet
hands.
i
•
Use a stabilized power adaptor designed for DC+12V± ± ± ±
W a r n i n g
10%, with a current capacity of more than 250mA for
the WAT-902H2/3 SUPREME.
The recommended voltage is DC+12V±10%
•
Do not expose the WAT-902H 2/3 SUPREME to wetness
or high moisture conditions.
The WAT-902H 2/3 SUPREME is designed and approved
for indoor use only. The WAT-902H 2/3 SUPREME is not
water-resistant or waterproof. If the location of the camera
is outdoors or in an outdoor like environment, we
recommend that you use an outdoor camera housing.
•
Protect the WAT-902H SUPREME from
2/3
condensation.
Keep the WAT-902H SUPREME dry at all times during
2/3
storage and operation.
•
Should the camera not work properly, switch off the power
immediately. Then check the camera according to the
"Problems and Trouble Shooting" section.
•
Avoid the striking of hard objects or dropping the WAT-
C a u t i o n
902H SUPREME.
2/3
The WAT-902H SUPREME uses high quality electrical
2/3
parts and precision components.
•
iDo not connect any power supply directly to the video
out terminal of the unit.
Do not connect the WAT-902H
2/3
monitor using a video/power single transmission terminal.
The WAT-902H SUPREME is not designed for use with
2/3
this type of equipment. We also advise you to read the
operation manual of the monitor you plan to use before any
connections are made.
•
Do not install the WAT-902H SUPREME in a position
2/3
subject to direct sunlight.
Sunlight shinning directly onto the WAT-902H
UPREME lens can cause damage to the CCD.
S
•
Select a stable place for installation of the WAT-
902H SUPREME.
2/3
Use a support of durable strength around an installation
position on a ceiling or wall when a camera stand or tripod
is used.
•
Do not move the WAT-902H 2/3 SUPREME with the
cables connected.
Before moving the WAT-902H 2/3 SUPREME, always
remove the video cable and power cable from the rear of
the camera first.
•
Avoid using the WAT-902H 2/3 SUPREME near any
strong electromagnetic field.
After installing into main equipment, if the WAT-902H
SUPREME is exposed to electromagnetic waves causing
the monitored image to become distorted, we recommend
the camera be shielded by appropriate protective casing.
Problems and Trouble Shooting
If any of the following problems occur when using the WAT-
902H 2/3 SUPREME,
•
An optimal picture cannot be obtained, after checking that all the
cables and connections are correctly in place
•
Smoke or any unusual odor emerges from the WAT-902H
SUPREME
•
An object becomes embedded or a quantity of liquid seeps into the
camera housing
•
More than the recommended voltage or/and amperage has been
applied to the WAT-902H SUPREME by mistake
2/3
•
Anything unusual occurring to any equipment connected to the
WAT-902H SUPREME.
2/3
Disconnect the camera immediately according to the following procedures:
①Switch off the main power supply to the camera.
2/3
②Remove the power and video cables connected to the WAT-902H
SUPREME.
③Contact the distributor or dealer from which the WAT-902H
SUPREME was purchased.
About EMC
The WAT-902H SUPREME is in conformity with EMC test standards
2/3
carried out by authorized organizations in Japan.
E I A /FCC Part15 class B
CCIR EN61000-6-3/EN50130-4
Do not modify the WAT-902H SUPREME. A modified
2/3
D a n g e r
camera may not conform to EMC test standards.
Contents
Using the contents figures below, check to make sure all parts are
present before use.
Lens Mount Cap WAT-902H SUPREME DC plug
2/3
Description of Parts
SUPREME with any
2/3
①CCD FRONT FACE
・The light receiving face of the CCD camera
(Dirt, water or oil deposits on the CCD will cause an unclear picture on
the monitor. Attach the lens cap to protect the lens and CCD from
2/3
contamination and damage.)
②LENS MOUNT
・Mount for the lens (Thread type)
③IRIS LEVEL VOLUME
・By controlling the volume, the iris level of a DC iris lens can be
adjusted.
④FOCUSING ADJUSTMENT SCREWS
・There are 3 hex. adjustment screws each placed at intervals of 120゜
for fine focusing of the lens.
⑤AUTO-IRIS SOCKET
2/3
・This socket is for a video or DC auto-iris lens cable connector.
(Video/DC: Auto selected by the camera)
⑥TRIPOD MOUNTING SCREW HOLES
・Mounting holes for stands. The size of these threads are 1/4", 20
threads, 4.5±0.2mm, which is the same as any standard camera
tripod (U1/4").
⑦AE MODE CONTROL
・
The switch for the shutter speed mode control according to the object
being monitored
2/3
⑧VIDEO OUT (BNC)
・The terminal for composite video signal output
2/3
⑨POWER IN
・The terminal designed for connection with the DC-plug of the power
adaptor
⑩AGC SELECTION SWITCH
・Switch for setting AGC HI or LO
Power Supply
Use a stabilized power adaptor designed for DC+12V±10%, with a
current capacity of more than 250mA.
Use the optional DC plug if the shape or polarity of the DC plug of the
power adaptor to be used is not compatible with the camera (See the
drawing on the right below).
W a r n i n g C a u t i o n
The wiring on the connector must be exact.
Be careful not to touch the other terminal while
wiring. Protect the wiring portion by using
Hex. Wrench
insulation tape after wiring. If the above care and
attention is not adhered to, damage to the
WAT-902H SUPREME and power adaptor may
2/3
occur and may also cause fire.
Iris Connector
Auto-iris Lens
Before connecting the auto-iris lens, please make sure that the pin
configuration is correct by confirming with the following table. If the
configuration of your iris connector is different from the following, the
plug and pins will need to be rewired.
EIAJ Video
Auto-iris Lens
Pin No.
Arrangement
④
②
① Power
② Not used
③ ① ③ Iris signals
④ Common (GND)
Set-up and Operation
1) Ensure that the power to the WAT-902H
peripheral equipment is turned off before making any connections.
2) Remove the lens mount cap from the WAT-902H
attach the CS-mount lens. Use the optional C-mount adaptor
(30CMA-R) when a C-mount lens is used.
3) Connect the iris control cable to ⑤AUTO-IRIS SOCKET on the
WAT-902H SUPREME when an auto-iris lens is being used.
2/3
4) Connect ⑧VIDEO OUT on the WAT-902H
monitor, using a coaxial cable with 75Ω impedance, such as an
. Select a monitor with the same television
RG-59 or an RG-6/U
system as the WAT-902H SUPREME: EIA or CCIR. A monitor with
2/3
more than 600TV lines is recommended.
5) Insert the power plug of the power adaptor into ⑨POWER IN on the
back panel of the WAT-902H SUPREME. Confirm that the power
2/3
adaptor is not connected to the power supply before insertion of the
power plug into ⑨POWER IN.
6) WAT-902H
Turn on the power to the
other allied equipment. When a picture cannot be obtained on the
monitor, or a problem occurs, check and follow the procedure mentioned
in the【Problems and Trouble Shooting】section.
7) After following the procedure below and the picture is still out of focus,
open the iris fully and loosen ④ FOCUSING ADJUSTMENT
SCREWS with the hex. wrench and move the lens forwards until a
clear picture is obtained.
Adjust the focus and iris to the best
Manual Lens
position on the lens.
Video Auto-iris Lens Adjust the focus on the lens.
Adjust the iris level on the camera, then
DC Auto-iris Lens adjust the focus on the lens. See
below.
Iris Level Adjustment (for DC auto-iris lenses)
Adjust ③IRIS LEVEL VOLUME placed on the side
of the unit until an acceptable light level is attained.
No change will occur if a video iris lens or manual
iris lens is fitted.
8) Set the shutter mode by ⑦AE MODE CONTROL.
(Shutter mode is set to EI upon shipment.)
AE Mode
Automatically selects the shutter speed in the range
EI between EIA: 1/60-1/100000 sec., CCIR: 1/50-
1/100000 sec. according to the lighting condition.
D C + 1 2 V
Reduces the flickering phenomena occurring on the
FL monitor screen caused by fluorescent or mercury
lamps.
C O M M O N ( G N D )
Fixes the shutter speed to EIA: 1/60 sec., CCIR: 1/50
OFF
sec..
EIAJ DC
Auto-iris Lens
Arrangement
Control －
Control ＋
Drive ＋
Drive －
2/3 SUPREME and the
2/3 SUPREME and
SUPREME with the
2/3
SUPREME
2/3 , monitor and all
C L O S E D
L E V E L
O P E N
Effect