Automatic Power Off - Pioneer Elite PRO-1000HD Operating Instructions Manual

Operations

Automatic Power OFF

This display is equipped with automatic power-
management and auto-power-off functions, which allow
the unit to automatically switch to power-saving mode
when no sync signal is detected.
(A warning message appears onscreen before these
functions operate.)
Notes
÷ Power Management settings are supported only when a
computer signal is input to INPUT 1.
÷ The auto-power-off function can be used only in those cases
other than the inputs used in the preceding item.
÷ Always turn off the plasma display's main power switch when
not using the display for extended periods of time.
1
Press MENU to display the menu screen.
MAIN MENU
PICTURE SCREEN
:
CO NT RA S T 0
:
BR I GHT . 0
: 6 +
R L E V E L . 0
: 6 0
G L E V E L . +
: 6 0
+
B L E V E L .
:
H E NH AN CE . 0
:
V E NH AN CE . 0
R S E T E
SELECT
SET
2 Press 2/3 to select SET UP.
[When computer signal is input to INPUT 1]
MAIN MENU
PICTURE SCREEN
I N P UT L A B E L
POWE R M NA GEME A
C L AMP P S I T I O N O
S E T T I N G
SELECT
SET
[In all other cases]
MAIN MENU
PICTURE SCREEN
I N P UT L A B E L
A U T O P OWE R
C L AMP P S I T I O N O
S E T T I N G
SELECT
SET
24
PRO-1000HD / PRO-800HD
INPUT1
SET UP OPTION
ENTER EXIT
MENU
INPUT1
SET UP OPTION
:
I N P UT 1
:
NT OF F
: A U T O
: V G A
ENTER EXIT
MENU
INPUT2
SET UP OPTION
: I N P UT 2
O F F : O F F
: A U T O
: V G A
ENTER EXIT
MENU
3 Press 5/∞ to select either the POWER
MANAGEMENT or AUTO POWER OFF mode.
[When computer signal is input to INPUT 1]
MAIN MENU
PICTURE SCREEN
I N P UT L A B E L
POWE R M NA GEME A
C L AMP P S I T I O N O
S E T T I N G
SELECT
SET
[In all other cases]
MAIN MENU
PICTURE SCREEN
I N P UT L A B E L
A U T O P OWE R
C L AMP P S I T I O N O
S E T T I N G
4
Press SET to confirm selection of the POWER
MANAGEMENT or AUTO POWER OFF.
3 OFF
ON 2
÷ When OFF is selected, the display will continue in
operating mode, regardless of the presence/
absence of an input sync signal.
÷ When POWER MANAGEMENT: ON is selected, if
a sync signal is not detected, a warning message is
displayed for 8 seconds, after which the display
automatically enters the power-saving mode (*1)
and the STANDBY/ON indicator flashes green. If a
sync signal (*2) is input again later, the plasma
display automatically returns to normal operating
mode.
*1. Power consumption about 1W
*2. Except when input signal is G on SYNC or composite
SYNC
÷ When AUTO POWER OFF: ON is selected, if no
sync signal is detected for 8 minutes or more, a
warning message will be displayed for 30 seconds,
after which the unit's power will switch to
STANDBY mode.
5
When the setup is finished, press MENU to exit
the menu screen.
Note
The POWER MANAGEMENT and AUTO POWER OFF functions
must be set individually for each input (INPUT 1–4).
To return to operating mode:
÷ To return to normal operation from POWER
MANAGEMENT mode: either operate the computer,
or press INPUT on the main unit operating panel or
remote control unit.
÷ To return to normal operation from AUTO POWER
OFF mode: Press STANDBY/ON on the main unit
operating panel or remote control unit.
INPUT1
SET UP OPTION
:
I N P UT 1
:
NT OF F
: A U T O
: V G A
CHANGE EXIT
MENU
INPUT2
SET UP OPTION
:
I N P UT 2
:
O F F O F F
: A U T O
: V G A